American Megatrends Megathon User Manual Download Page 38 | Manualshive

Page: 38 / 55

background image

Megathon PCI Motherboard User’s Guide

32

AMIBIOS Main Menu Setup,

Continued

Auto-Detect Hard Disks

This allows the system BIOS to detect the hard disk parameters

automatically.

Boot Sector Virus Protection

This option is near the bottom of the Main Setup screen. The

settings are

Enabled

or

Disabled.

Choose

Enabled

to enable boot sector

protection. AMIBIOS displays a warning when any program (or virus) issues a
Disk Format command or attempts to write to the boot sector of the hard disk
drive. If enabled, the following appears when a write is attempted to the boot
sector. You may have to type

N

several times to prevent the boot sector write.

Boot Sector Write!!!

Possible VIRUS: Continue (Y/N)? _

The following appears after any attempt to format any cylinder, head, or sector of
any hard disk drive via the BIOS INT 13 Hard Disk Drive Service:

Format!!!

Possible VIRUS: Continue (Y/N)? _

«
...
36
37
38
39
40
...
»

Summary of Contents for Megathon
























































Reviews:

No comments

Related manuals for Megathon

Brand: Aaeon Pages: 132

Brand: Aaeon Pages: 50

Brand: Abit Pages: 112

Brand: ST Pages: 79

Brand: NXP Semiconductors Pages: 269

DS-5116HFI Series

Brand: HIKVISION Pages: 22

KEMX-1600 Series

Brand: Quanmax Pages: 74

Brand: ICP Pages: 50

Brand: Safran Pages: 29

Brand: Advantech Pages: 5

Brand: Biostar Pages: 210

Brand: Gigabyte Pages: 112

Brand: Gigabyte Pages: 34

Brand: Wolfson Pages: 46

Brand: STMicroelectronics Pages: 17

Brand: Albatron Pages: 33

Brand: DataExpert Pages: 52

S2257 THUNDER 2400

Brand: TYAN Pages: 105

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands