background image

ADJ Products, LLC  -  www.adj.com  - WiFLY Bar QA5 User Manual Page 15

ADJ Products, LLC  -  www.adj.com  - WiFLY Bar QA5 User Manual Page 16

  WiFLY Bar QA5                        Master-Slave Configuration 

Master-Slave Configuration:

 

This function will allows you to link units together to run in a Master-Slave 

mode. In Master-Slave operation one unit will act as the controlling unit 

and the others will react to the controlling units built-in programs. Any 

unit can act as a Master or as a Slave however, only one unit can be pro-

grammed to act as the “Master.” 
Master-Slave Connections and Settings:

1.   Daisy chain your units via the XLR connector on the rear of the unit.  

  Use standard XLR data cables to link your units together. Remember 

  that the Male XLR connector is the input and the Female XLR con- 

  nector is the ouput. The first unit in the chain (master) will use the  

  female XLR connector only. The last unit in the chain will use the   

  male XLR connector only. 

2.   Set the “Master” unit to your desired mode of operation.

3.   On the “Slave” units press the MODE button 

until “SLAu” is dis-  

    played. The unit is now set as the “Slave” unit. Each slave unit  

    must be set to the same setting.

4.   Connect the first “Slave” unit to the “Master”, and the “Slave” unit 

    should now start follow the “Master”.

  WiFLY Bar QA5                                               WiFly Set Up 

  WiFLY Bar QA5                         WiFly Master-Slave Set Up 

With this feature you are able to control the unit with DMX without the 

need of XLR cables. Your DMX controller must be connected to a ADJ 

WiFly TransCeiver to use this function. You are able to communicate 

up to 400 feet (open line of sight)

NOTE: The ADJ RFC control must be set to OFF to use this func-

tion.

1.   Turn on the WiFly function using the WiFly On/Off switch and   

    set the attenna to a upright position.

2.   Follow the instructions on page 14 to set the Wireless address.  

    The address must match the address set on the WiFly Transceiver.

3.   After you have set the WiFly address, follow the DMX instructions  

    on pages 12-13 to select your desired DMX Channel mode and  

    set your DMX address.

4.   Apply power to the ADJ WiFly Transceiver. The fixture must be set  

    up first before you apply power to WiFly Transceiver.

5.   If everything is set up properly and the fixture is receiving a    

    Wireless signal, Wireless status LED next to LED screen will glow 

    green. Note: If the sync does not work, switch the WiFly power off  

    then on again.

This feature will let you link units to run in a master-slave mode with-

out the use of XLR cables. 

NOTE: The ADJ RFC control must be set to OFF to use this func-

tion.

1.   Follow the instructions on page 14 to set the Wireless address. 

    The addresses on each fixture must be the same.

2.   After you have set the WiFly address, select your master unit and  

    set your desired operating mode.

3.   Put the attenna to a upright position then turn the WiFly On, using  

    the WiFly power switch.

4.   For the Slave units, put the unit in Slave mode. See page 15    

    Master-Slave configuration when setting the unit as a Slave. Then  

    switch ON the WiFly power switch.

4.   If everything is set up correctly, the Master units WiFly status LED  

    will glow orange, and the slave units Wireless status LED will glow 

   green. 

NOTE: If they do not sync up master-slave, switch the Master fix-

tures WiFly power switch off then on again.

Summary of Contents for WIFLY BAR QA5

















Reviews: