background image

ADJ Products, LLC  -  www.adj.com  - WiFLY Bar QA5 User Manual Page 11

ADJ Products, LLC  -  www.adj.com  - WiFLY Bar QA5 User Manual Page 12

  WiFLY Bar QA5                               Operating Instructions

    This is the base color, use the UP and DOWN buttons to scroll    

    through the 15 colors. Once you have chosen your base color, press  

    the SET UP button again so that“C2.XX” is displayed. This is the   

    moving color, use the UP and DOWN buttons to scroll through the 15  

   colors.

Sound Active Mode:

In this mode the WiFLY Bar QA5 will react to sound, and chase 

through the different colors.

1.   Plug the fixture in and press the MODE button until “SU.XX” is  

    displayed. “XX” represents the sound sensitivity level (0-31) cur- 

    rently displayed.

2.   The fixture will now change via sound.

3.   Press the SET UP button to enter the Flash (strobe) mode.

4.   “FS.XX” will be displayed, this is Flash mode. The Flash can be 

    adjusted between “FS.00” (flash off) to “FS.15” (fastest flash).

Auto Run Mode: 

In this mode the WiFly Bar QA5 will run a auto program.

1.   Plug the fixture in and press the MODE button until “AUTO” is dis- 

   played.

2.   After you have activated Auto Run mode, press the SET UP but- 

    ton to adjust the fade time. 

3.   Once you press SET UP “Fd.XX” should be displayed. Use the UP  

    or DOWN buttons to set the fade speed to either “Fd.00” (fade  

    off) or between “Fd.01” (fastest speed) and “Fd.99” (slowest    

    speed). After adjusting the fade speed, press SET UP if you    

    wish to activate the Flash mode.

4.   “FS.XX” will now be displayed, this is Flash mode. The Flash can  

    be adjusted between “FS.00” (flash off) to “FS.15” (fastest flash).

DMX Mode:

Operating  through  a  DMX  controller  gives the user the freedom to 

create their own programs tailored to their own individual needs. This 

function also allows you to use your fixtures as spot lights. The WiFLY 

Bar QA5 has 6 DMX modes: 4 Channel mode, 6 Channel mode, 7 

Channel mode, 8 Channel mode, 9 Channel mode, and a 22 Channel 

mode, See pages 18-25 for each modes’ DMX traits.

1.  This function will allow you to control each individual fixture’s   

  traits with a standard DMX 512 controller.

  WiFLY Bar QA5                               Operating Instructions

RGBA Dimmer Mode:

1.   Plug the fixture in and press the MODE button until: 

2.   When “r.XXX” is displayed you are in Red dimming mode. Press  

    the UP and DOWN buttons to adjust intensity.

3.   When “G.XXX” is displayed you are in Green dimming mode.    

    Press the UP and DOWN buttons to adjust intensity.

4.   When “b.XXX” is displayed you are in Blue dimming mode. Press  

    the UP and DOWN buttons to adjust intensity.

5.   When “U.XXX” is displayed you are in Amber dimming mode.   

    Press the UP and DOWN buttons to adjust intensity.

6.   After you have adjusted the RGBA colors to make your desired  

    color you can then activate strobing by pressing the SET UP but- 

    ton to enter the Flash (strobe) mode.

7.   “FS.XX” will be displayed, this is Flash mode. The Flash can be 

    adjusted between “FS.00” (flash off) to “FS.15” (fastest flash).

Built-In Program Mode:

1.   Plug the fixture in and press the MODE button until “Pr.XX” is dis-

    played. “XX” represents a number from 1-22. Use the UP or DOWN  

    buttons to scroll through the 22 programs. Programs 21 and 22    

    have adjustable colors. Once you have found your desired program  

    press the SET UP button.

2.   Pressing the SET UP button will display “SP.XX”. When this is dis- 

    played you can adjust the running speed of your desired program.  

    Use the UP or DOWN button to adjust the speed between “SP.01”  

    (slowest) and “SP.99” (fastest). Once you have set your desired run- 

    ning speed, you can press the SET UP button to to enter the Fade  

    adjustment mode.

2.   Pressing the SET UP button will display “Fd.XX”. When this is dis- 

    played you can adjust the fade speed of your desired program.    

    Use the UP or DOWN button to adjust the speed between “Fd.01”  

    (fastest) and “Fd.99” (slowest) or “Fd.00” (Off). Once you have set  

    your desired fade speed, you can press the SET UP button to to   

    enter the Flash (Strobe) mode. 

3.   After pressing SET UP, “FS.XX” will be displayed, this is Flash mode.  

    The Flash can be adjusted between “FS.00” (flash off) to “FS.15”  

    (fastest flash).

•    PROGRAMS 21 & 22 - If you have chosen programs 21 or 22, after  

    the  Flash mode, press the SET UP button. “C1.XX” will be displayed.  

Summary of Contents for WIFLY BAR QA5

















Reviews: