background image

©

American DJ

®

  -  www.Americandj.com  - Jelly GO Par64 User Manual Page 5

©

American DJ

®

  -  www.Americandj.com  - Jelly GO Par64 User Manual Page 6

1. Handling of Batteries

1.1 Do Not Short Circuit the Battery

Try to never short circuit the battery. It generates a very high 

current which could cause the battery to overheat which may 

result in electrolyte gel leakage, harmful fumes, or explosion. 

The LIR tabs may easily short-circuit by placing them on con-

ductive surface. A short circuit may lead to heat build up and 

damage of the battery. An appropriate circuitry with PCM is 

employed to protect accidental short circuit of the battery pack.
1.2 Mechanical shock

Droping the unit, impact hit, bending, etc. may cause failure or 

shortend life of the LIR battery.
3. Other

3.1 Battery connection

1). Direct soldering of wire leads or devices to the battery is 

strictly prohibited.
2). Lead tabs with pre-soldered wiring shall be spot welded to 

the batteries. Direct soldering may cause damage of compo-

nents, such as separator and insulator, by heat build up.
3.2 Prevention of short circuit within a battery pack

There is enough insulation layers between wiring and the bat-

teries to provide extra safety protection. The battery pack is 

constructed in a way that no short circuit will occur which may 

cause smoke or fire.
3.3 Do No Disassemble the Batteries

1). Never disassemble the batteries.

Doing this may cause a internal short circuit in the battery, 

which may lead to harmful fumes, fire, explosion, or other prob-

lems.
2). Electrolyte Gel is harmful

Electrolyte Gel should not leak from the LIR battery. Should the 

electrolyte gel come into contact with the skin or eyes, flush the 

area of contact immediately with fresh water and seek medical 

attention immediately.
3.4 Do Not Expose the Battery to Heat or Fire

Never incinerate or dispose of the batteries in fire. This may 

cause an explosion, which would be very dangerous.
3.5 Do Not Expose the Battery to water or liquids

Never soak/drop the batteries in liquids such as water, seawa-

ter, drinks such as soft drinks, juices, coffee or other.
3.6 Battery Replacement

For battery replacement please contact American DJ customer 

support (800) 322-6337.
3.7 Do Not use a damaged Battery

The battery could be damaged during shipping, caused by 

shock. Should the battery be found damaged, including dam-

ages to the plastic casing of the battery, deformation of the 

battery package, smelling of an electrolyte, or leakage of the 

electrolyte gel, or other, DO NOT use the battery. A battery with 

a odor of electrolyte or a gel leakage should be placed away 

from fire to avoid fire or explosion.
4. Battery Storage

When storing the battery, it should be stored at room tempera-

ture, with a charge of at least 50%. We recommend that during 

long periods of storage that the battery be charged every 6 

months. Doing this will prolong the life of the battery and will 

also make sure that the battery charge does not fall below the 

30% mark.
5. Other Chemical Reaction

Because batteries utilize a chemical reaction, battery per-

formance will deteriorate over time even if stored for a long 

period of time without being used. In addition, if the various 

usage conditions such as charge, discharge, ambient tempera-

ture, etc. are not maintained within the specified ranges, the 

  Jelly GO Par64                                   Battery Precautions

  Jelly GO Par64                                   Battery Precautions

Summary of Contents for Jelly GO Par64















Reviews: