©
American DJ
®
- www.Americandj.com - Jelly GO Par64 User Manual Page 11
©
American DJ
®
- www.Americandj.com - Jelly GO Par64 User Manual Page 12
Jelly GO Par64 Operating Instructions
the color fade is off, and the fixture will now color change at
the speed you have set. To run the fixture in color fade, reverse
the instructions. Set your color fade speed and set the color
change speed to “SP.01”.
RGB Dimmer Mode:
1. Plug the fixture in and press the MODE button until:
2. When “r.XXX” is displayed you are in Red dimming mode. Press
the UP and DOWN buttons to adjust intensity.
3. When “G.XXX” is displayed you are in Green dimming mode.
Press the UP and DOWN buttons to adjust intensity.
4. When “b.XXX” is displayed you are in Blue dimming mode. Press
the UP and DOWN buttons to adjust intensity.
5. After you have adjusted the RGB colors to make your desired
color you can then activate strobing by pressing the SET UP but-
ton to enter the Flash (strobe) mode.
6. “FS.XX” will be displayed, this is Flash mode. The Flash can be
adjusted between “FS.00” (flash off) to “FS.15” (fastest flash).
DMX Mode:
Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs. This
function also allows you to use your fixtures as spot lights. The Jelly
GO Par64 has 7 DMX modes: 1 Channel mode, 2 Channel mode, 3
Channel mode, 4 Channel mode, 5 Channel mode, 6 Channel mode,
and a 7 Channel mode. See pages 18-22 for each modes’ DMX traits.
1. This function will allow you to control each individual fixture’s
traits with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until
“A.XXX” is displayed. “XXX” represents the current displayed ad-
dress. Use the UP or DOWN buttons to select your desired DMX
address, then press the SETUP button to select your DMX
Channel mode.
3. Use the UP or DOWN buttons to scroll through the DMX Channel
modes. The Channel modes are listed below:
To run the 1 Channel Mode, press the MODE button until “Ch.01”
is displayed. This is the 1 Channel DMX Mode.
To run the 2 Channel Mode, press the MODE button until “Ch.02”
is displayed. This is the 2 Channel DMX Mode.
Jelly GO Par64 Operating Instructions
as the American DJ® Show Designer™.
Sound Active Mode:
In this mode the Jelly GO Par64 will react to sound, and chase
through the different colors.
1. Plug the fixture in and press the MODE button until “SoXX” is dis-
played. “XX” represents the sound active mode (1-15) currently
displayed.
2. The fixture will now change via sound.
3. Press the SET UP button to adjust the sound sensitivity. “SJ-X”
should be displayed. Use the UP or DOWN buttons to adjust the
sensitivity. “SJ-1” is the lowest sensitivity, “SJ-8” is the highest.
Static Color Mode:
1. Plug the fixture in and press the MODE button until “CLXX” is
displayed.
2. There are 32 colors to choose from. Select your desired color by
pressing the UP and DOWN buttons. After you have selected your
desired color you can activate strobing by pressing the SET UP
button to enter the Flash (strobe) mode.
3. “FS.XX” will be displayed, this is Flash mode. The Flash can be
adjusted between “FS.00” (flash off) to “FS.15” (fastest flash).
Auto Run Mode:
In this mode the Jelly GO Par64 will run 1 of 16 auto programs. The
auto run program can be either a fade program or a simple color
change program.
1. Plug the fixture in and press the MODE button until “APXX” is dis-
played. “XX” represents the program number (1-16) currently dis-
played.
2. After you have chosen your desired program you need to decide
if you would like the program to fade through colors or simply
change. Press the SET UP button until either “SP.XX” (color
change) or “F-XX” (color fade) is displayed.
3. If you select color change, use the UP and DOWN buttons to
adjust the speed between “SP.01” (slowest) and “SP.99” (fastest).
Once you have set your desired color change speed, press the
SET UP button to move on to “F-XX” (color fade). Use the UP or
DOWN buttons to set the color fade speed to “F-00”. This means
