![background image](http://html1.mh-extra.com/html/american-dj/dura-spot-150/dura-spot-150_user-instructions_2922695010.webp)
American DJ
®
- www.americandjeurope.com - Dura Spot 150™ Instruction Manual Page 10
Dura Spot 150™
System Menu
MENUS:
To access these menus you must press the ESC button
twice and then press the UP button until you find the specific menu
you are looking for.
A001:
At this menu you can set the DMX address. Press the Enter
button, and the “A” will start flashing. Press the UP or Down buttons
to find your desird address. When you have found your desired ad-
dress press the Enter button to set it.
TEST:
In this menu you can select one of three test modes to run.
Using the Up button scroll to “test” and press Enter. It will now
display “Mode 1”. You can scroll to another test mode by press-
ing the Up button. To select your desired test mode press the Enter
button. Then press the Up button to access the Speed menu. Adjust
the speed, and then press the ESC (Escape) button. The test mode
should now be activated. To pause the test mode, press Enter. If you
want to stop test mode, pause it and then press ESC.
AUDI:
In this menu you can activate Sound Active mode. Using the
Up button scroll to “AUDI” and press Enter. Press the Up button until
“On” is displayed, and press Enter. Now, press ESC, so that the ad-
dress is showing. It will take about 10 sec. for Sound Activity to start.
The display will flash TEST RUN. Don’t worry the unit will be sound
active.
REVERSE PAN (RPAN):
In this menu you can reverse the Pan func-
tion. Using the Up button scroll to “rPan” and press Enter. Press the
Up button until “On” is displayed, and press Enter. Now, press ESC.
This function works better when you have two units connected in a
Master/Slave setup. Have one unit set to reverse Pan and the other
unit left in normal Pan.
REVERSE TILT ( RTILT):
In this menu you can reverse the Tilt func-
tion. Using the Up button scroll to “rTilt” and press Enter. Press the
Up button until “On” is displayed, and press Enter. Now, press ESC.
This function works better when you have two units connected in a
Master/Slave setup. Have one unit set to reverse Tilt and the other
unit left in normal Tilt.
DISP (Display):
In this menu you can “flip” the display 180°. Using
the Up button scroll to “disp” and press Enter. “Turn” should now be
American DJ
®
- www.americandjeurope.com - Dura Spot 150™ Instruction Manual Page 19
Dura Spot 150™
Fuse & Lamp Replacement
Caution:
Always replace with the exact same type lamp and fuse,
unless otherwise specified by an authorized American DJ
®
service
technician. Replacing with anything other than the specified part can
damage your unit and will void your manufactures warranty.
Warning:
If you continue to blow lamps or fuses, STOP using the
unit. Contact customer support for further instructions, you may have
to return the unit for servicing. Continuing to use the unit may cause
serious damage.
Lamp Replacement:
Caution! Never attempt to change the lamp
while the fixture is plugged in. Always disconnect the main power
and allow the unit ample time to cool before attempting to replace
the lamp. Lamp replacement has been made simple by incorporating
a slide out lamp assembly that is retained by two phillips screws.
1. Be sure to follow the proper handling procedures that deal with
discharge lamps.
2. Remove the two small screws (A,B) on the rear of the unit
3. After removing the screws, gently slide out the socket assembly
from the rear of the unit to expose the lamp.
4. Carefully remove the old lamp and discard it in the trash.
5. Replace the lamp with an exact match and reassemble in reverse
order.
6. After replacing the lamp follow the optimization procedures on the
next page to be sure the lamp is center in the reflector
A
B