background image

Unpacking: 

Thank you for purchasing the Dura Spot 150™ by Ameri-

can DJ

®

. Every Dura Spot 150™ has been thoroughly tested and has 

been shipped in perfect operating condition. Carefully check the ship-
ping carton for damage that may have occurred during shipping. If the 
carton appears to be damaged, carefully inspect your fixture for any 
damage and be sure all equipment necessary to operate the unit has 
arrived intact. In the event damage has been found or parts are miss-
ing, please contact our toll free customer support number for further 
instructions. Please do not return this unit to your dealer without con-
tacting customer support first. 

Introduction: 

This unit is a 8 channel DMX intelligent scanner. It can 

be run as a stand-alone, sound active unit, DMX controlled unit, or in 
a Master/Slave configuration. This unit has been tested and the lamp 
has been installed at the factory, there is no assembly required. The 
unit is ready to be plugged in to a power outlet. There are no dipswitch 
settings for Master/Slave mode, just simply link the units together. To 
enhance the beams effects you can use a fog machine. This unit looks 
good in pairs.

 

During the initial start-up or use of this product a light smoke or 
smell  may  arise  from  the  unit.  This  is  a  normal  process  and  is 
cause by the heat associated with the lamp.

 

Customer  Support:

  American  DJ  Europe

®

  provides  a  customer 

support line, to provide help and to answer any question should you 
encounter problems during your set up or initial operation. You may 
also visit us on the web at www.americandjeurope.com for any com-
ments or suggestions. Service Hours are Monday through Friday 9:00 
a.m. to 5:00 p.m.
 

Voice:   

+31 45 546 85 00

 

Fax: 

  

+31 45 546 85 99

 

E-mail:  

[email protected]

Warning! 

To prevent or reduce the risk of electrical shock or fire, do 

not expose this unit to rain or moisture. 

Warning! 

This may cause severe eye damage. Avoid looking directly 

into the light source at all times!

  Dura Spot 150™         

                             General Information

American DJ

®

  -  www.americandjeurope.com  - Dura Spot 150™ Instruction Manual Page 3

American DJ

®

  -  www.americandjeurope.com  - Dura Spot 150™ Instruction Manual Page 26

 Dura Spot 150™    

 

 

                        Notes

Summary of Contents for Dura Spot 150















Reviews: