Amazone Ceus 4000-2TX Operating Manual Download

Page: 102 / 132

Cleaning, maintenance and repairs

WARNING

Risk of contusions, cutting, catching, drawing in and knocks
through

•

unintentional falling of the machine raised using the trac-
tor's three-point hydraulic system.

•

unintentional falling of raised, unsecured machine parts.

•

unintentional start-up and rolling of the tractor-machine
combination.

Secure the tractor and machine against unintentional starting and
unintentional rolling away before you perform any cleaning, servicing
or maintenance work on the machine. See page 78.

DANGER!

•

During cleaning, maintenance and repair work, observe
chapter "Safety instructions for the user" from page Seite
30,

•

Always use suitable supports when carrying out mainte-
nance work on the raised machine.

•

Check the proper function of the light system!

•

After repair work involving repainting, the product logos and in-
struction signs must be replaced!

•

Worn and damaged parts must be replaced. Use only OEM
spare parts!

•

All marked lubrication points must be lubrication according to the
lubrication plan (page 104) and the sliding and pivot points
greased accordingly!

•

Clean the tools after work!

102

Ceus-2TX BAG0183.2 01.19

Summary of Contents for Ceus 4000-2TX





































































































































Search results

Summary of Contents for Ceus 4000-2TX

Reviews:

Related manuals for Ceus 4000-2TX

Brands by name

Popular brands

Amazone Ceus 4000-2TX, Operating Manual

Search results

Summary of Contents for Ceus 4000-2TX

Reviews:

Related manuals for Ceus 4000-2TX

Brands by name

Popular brands