Amazone Ceus 4000-2TX Operating Manual Download

Page: 75 / 132

Commissioning

6.1.2.2

Compare the permissible D

value with actual D

value

WARNING

Danger from breaking the coupling devices between the tractor
and the implement when the tractor is not used for its intended
purpose!

1. Calculate the actual D

value of your combination, comprising

tractor and implement.

2. Compare the actual D

value with the following permissible D

values:

•

Coupling device of the implement

•

Drawbar of the implement

•

Coupling device of the tractor

The actual D

value calculated for the combination must be less than

or equal (

≤

) to the D

values specified.

The permissible D

values of the implement can

be found on the rating plate of the coupling de-
vice (1) and the drawbar (2).

The permissible D

value of the tractor coupling

device can be found directly on the coupling
device / in the operating manual of your tractor.

actually calculated
D

value for the combination

specified D

value

≤

Coupling device on the tractor

≤

Coupling device of the implement

≤

Drawbar of the implement

Ceus-2TX BAG0183.2 01.19

Summary of Contents for Ceus 4000-2TX





































































































































Search results

Summary of Contents for Ceus 4000-2TX

Reviews:

Related manuals for Ceus 4000-2TX

Brands by name

Popular brands

Amazone Ceus 4000-2TX, Operating Manual

Search results

Summary of Contents for Ceus 4000-2TX

Reviews:

Related manuals for Ceus 4000-2TX

Brands by name

Popular brands