![background image](http://html1.mh-extra.com/html/amano/07104/07104_operators-manual_2918214007.webp)
CAUTION:
This machine will operate only on AC frequency and on electrical voltage shown on the motor nameplate. Make
sure you have the correct frequency and voltage before connecting the power cord to an outlet. The machine has
a plug as shown below.
DANGER:
Electrocution could occur if the machine is exposed to water or rain. Keep the machine in a dry building.
DANGER: Electrocution could occur if machine is improperly connected to the electrical system. To prevent possible electric
shock, always use a 3 -wire electrical system connected to an electrical ground. For maximum protection against
electrical shock, use a circuit that is protected by a ground fault circuit interrupter. Consult your electrical
contractor.
DANGER:
Electrocution could occur if the ground pin is tampered with in any way. Do not cut, remove, or break the ground
pin. Do not try to fit a three-terminal plug into a receptacle or connector body other than a three-plug receptacle
or connector body. If the outlet does not fit the plug, consult your electrical contractor.
DANGER:
Electrocution could occur if the machine is used with a damaged plug or power cord. If the cords or plugs are worn
or damaged in any way, have them replaced by an authorized service person or electrician.
If motor appears to labor or takes a considerably longer time to come up to speed, reduce sanding pressure.
Machine Specifications
Introduction
The FloorCrafter can be used on a variety of surfaces. It is an ideal tool for wood flooring maintenance and restoration work.
7
230V Electrical Connection Instructions
This machine must be connected to an electrically grounded circuit in order to
protect the operator from electric shock. This machine has an approved power
cord with three conductors as well as a plug with three terminals. Connect the
plug into a three holed receptacle. For maximum protection against electric
shock, use a circuit that is protected by a ground fault circuit interrupter.
Extension Cords
Use only an approved three-pronged extension cord with two main conductors
and one earthing conductor. This machine is equipped
with a power cord. When greater range is needed follow the table
to determine cable gauge of additional footage. Refer to the
chart to the right for extension cord information
EN
Part #
07104A
07104B
07202B / 07104C
56380917
Model
FloorCrafter 8
FloorCrafter 8, Blk
FloorCrafter 8
FloorCrafter 8
Electrical Requirements
230~, 60Hz / 15.7 A, 3.7 kW
230~, 60Hz / 15.7 A, 3.7 kW
230~, 60Hz / 15.7 A, 3.7 kW
230~, 50Hz / 16.0 A, 3.0 kW
Sound Emission (Lpm)*
93.0 dB(A)
93.0 dB(A)
93.0 dB(A)
96.2 dB(A)
Vibration
<.15 in/s
<.15 in/s
<.15 in/s
2.88 m/s
2
rms
Motor
4 Hp Induction
4 Hp Induction
4 Hp Induction
3 kW Induction
Contact Wheel Rate
2450 rpm
2450 rpm
2450 rpm
2042 rpm
Abrasive Rate
4500 ft/min
4500 ft/min
4500 ft/min
3750 ft/min
Abrasive Size
29
½
” x 7
⅞
”
29
½
” x 7
⅞
”
29
½
” x 7
⅞
”
29
½
” x 7
⅞
”
Fan Flow Rate
234 CFM
234 CFM
234 CFM
195 CFM
Drum Settings
80 lbs., 70lbs., 60 lbs.
80 lbs., 70lbs., 60 lbs.
80 lbs., 70lbs., 60 lbs.
80 lbs., 70lbs., 60 lbs.
Overload Protection
Magnetic Circuit Breaker
Magnetic Circuit Breaker
Magnetic Circuit Breaker
Magnetic Circuit Breaker
Electric Cable
50’, 10-3 SJO LP-20P Plug
50’, 10-3 SJO LP-20P Plug
50’, 10-3 SJO LP-20P Plug
100’, H05VVF3G4.0 AV3-20P Plug
Operating Controls
Adjustable Lever/Grip
Adjustable Lever/Grip
Adjustable Lever/Grip
Adjustable Lever/Grip
Leveling Controls
Externally Adjustable
Externally Adjustable
Externally Adjustable
Externally Adjustable
Operating Wheels
80 Durometer Clear Urethane
80 Durometer Clear Urethane
80 Durometer Clear Urethane
80 Durometer Clear Urethane
Weight
204 lbs.
204 lbs.
204 lbs.
204 lbs.
Dimensions
35 x 13
¾
x 38
¾
35 x 13
¾
x 38
¾
35 x 13
¾
x 38
¾
35 x 13
¾
x 38
¾
Summary of Contents for 07104
