background image

Full Height Tandem Installation Instructions

Page 16                [email protected]   +1(909) 591-8431   www.alvaradomfg.com  

Installation Instructions

 

Final Mechanical Installation Steps

Fig. 23

 

Drill

9/64" Drill Bit

#10 x ¾" Phillips  

pan head screw

Screwdriver

NOTE

 

Be sure that the turnstile is level  

 

 

 

before performing the following step(s). 

1. 

The anchor bolts (22 total) and the Top  

 

Channel mounting bolts should be tightened to  

 

40 ft-lbs using a torque wrench and appropriate  

 sockets. 
2. 

Using a drill and 9/64" drill bit, pre-drill six holes  

 

through the guard plate and into the Yoke (three  

 

along each side of the Yoke).

3. 

Insert and tighten six #10 x ¾" Phillips pan head  

 

screws (Figure 23).

 

4. 

Test the Roto for binding when it is functional. If  

 

there is  binding, loosen the mounting hardware and  

 

adjust as needed.

5. 

Test the Roto for binding. If no binding occurs,  

 

retighten all mounting hardware.

6. 

Repeat all previous steps for the second Guard  

 

Plate installation.

Key turned  

90°

Roto

Top 

Channel

Guard  

Plate

Fig. 24

NOTE

 

When shipped, the keys are attached to the chassis on the 

inside of the top channel.
The key override switch manually unlocks the turnstile in the 

desired direction. Key override switches are installed in the 

Top Channel, on either side of the Roto. 
To engage the key override, turn the key 90°.

NOTE

 

Remove keys when complete and store in a safe location. 

If the key override lock will not properly engage, please refer 

to the 'Troubleshooting' section.
This completes your installation 

of the MST. 
If the MST is electrically controlled,  

please proceed to the "Electrical  

Wiring Instructions" section.

Key

Key Override Operation

Non-Override

Override

NOTE

 

The key will always be parallel to the Top Channel in  

the override position. The key will always be  

perpendicular to the Top Channel in the non-override 

position.

Mounting Hole

Mounting Screw

 

Fig. 23A

23A Inset

Guard Plate Edge

¼-20 x 1" Screw

9/64" Drill Bit

CPST-T and CLST-T Installations

 

1. 

With the guard plate in place, use a pencil  

 

and mark each screw location. Each location  

 

should line up with the upper mounting  

 

channel mounting screw (Appendix A - A9),  

 

3/4" from the edge of the guard plate.

2. 

Using a drill and 9/64" drill bit, pre-drill four  

 

holes (two for each side of the Yoke).

3. 

Insert and tighten four #10 x ¾" Phillips pan  

 

head screws (Figure 23A inset).

Summary of Contents for CLSTT-3















































Reviews:

Related manuals for CLSTT-3