background image

INSTALLATION

Deluxe Control Cook & Hold   

   Operator’s Manual   

   MN-46708   

   Rev 1   

   1/20

19

Continued from previous page

Continued on next page

Electrical

Alto-Shaam oven ratings

Breaker:

Voltage:

Phase:

Cord:

Plug:

Is the oven going to be hard wired?

Yes

No

The following fields must be completed by the service technician on site.

What is the measured voltage at the site?

L1-N:

L2-N:

L3-N:

L1-L2:

L2-3:

L1-L3:

Pass

Fail

What is the on-site breaker size supplying 

power to the oven(s)?

Size:

Pass

Fail

Is there a disconnect or junction box within 

3’ (914mm) of where the oven(s) will be 

installed?

Pass

Fail

Comments:

Wifi equipped ovens

Is the Wifi system that be used secure, Wifi Protected Access 2 (WPA2)? The 

Wifi system to be used cannot be Point of Sales Wifi.

Yes

No

Have you been provided the Service Set Identifier (SSID) for the system to be 

used?

Yes

No

Have you been provided the pass phrase for the Wifi system to be used?

Yes

No

At the final location that the oven will be installed, can you connect to the Wifi 

system with your phone?

Yes

No

At the final location that the oven will be installed, can you connect to Alto-

Shaam.com with your phone using the Wifi system?

Yes

No

Is site action required?

Yes

No

Action required:

Other site information

Is there a proper ventilation hood installed above where the oven(s) will be installed?

(If required)

Pass

Fail

Does the designated location for the oven have a level surface, i.e., no more than 1.5” 

(38mm) change in elevation from its highest to lowest surface point?

Pass

Fail

Is the site 100% ready for oven(s) installation?

Pass

Fail

Is site action required?

Pass

Fail

Action required:

Summary of Contents for 1000-TH Split Series





































































Reviews: