Altice Labs D2260G, Manual, Page: 39 / 39

297x105
1
2
x
Smart Wi - Fi Extender
Power Supply Unit
Quick Guide
IN THE BOX
© 20 20 Altice Labs. All rights reserved.
April
20
20
HOW TO CONNECT YOUR NEW SMART Wi-Fi EXTENDER
Aveiro - Portugal
Rua Eng. José Ferreira Pinto Basto
3810 - 106 Aveiro (Portugal)
www.alticelabs.com
https://www.alticelabs.com/en/connectivity.html
DECLARATION
OF
CONFORMITY
Smart Wi-Fi Extender
Quick Guide
1
2
Icon Color Description
Off
Press this button to turn on
On
To turn off, press this button until the lights go off
Off
The WiFi is disabled
Flashing red
The extender is not paired with the router
Flashing white Poor connection between extender and router
Red No connection between extender and router
White
Good connection to the router
WPS
Off
Automatic pairing is not available
WPS
Flashing white
Pairing in progress
WPS
White
Automatic pairing is available
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION:
The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such
modifications could void the user's authority to operate the equipment. IEEE 802 11b or 802 11g operation of this product in the USA is
firmware limited to channel 1~11. This device is restricted for indoor use.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed
and operated with minimum distance 20 cm between the radiator and your body. This device and it's antennas(s) must not be co-located
or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.
5GHz Wireless Statement:
For operation within the 5.15~5.25GHz and 5 . 725 -5.85 GHz frequency ranges, this device is restricted to indoor environments.
This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.
Safety Warnings:
The Smart Wi-Fi Extender is a device that uses passive cooling, t o avoid overheating please do not block the ventilation holes.
Environmental conditions to be complied with at the installation site: humidity (0% to 95%) and temperature (41ºF to 104ºF).
FEDERAL COMMUNICATION COMMISSION (FCC)
INTERFERENCE STATEMENT
MANUAL INSTALLATION IN 2 STEPS
1. Pairing the Smart Wi - Fi Extender
Plug your extender into a power outlet near your router.
If the buttons remain off, press the power button to start your extender.
Wait for the light to flash red.
Press the
WPS button on your extender and the WPS button on your router.
Wait until the light is solid white.
Your extender is paired, you can now disconnect it.
2. Position the extender
Place the extender in the desired location and plug it on. For best results,
connect your extender halfway between your router and the area to be
covered by WiFi .
If the light is solid white, the installation is complete.
If the light flashes white or is solid red, move the extender closer to your
router.