55
-EN
MobileHub™ Link
(Optional)
About MobileHub™ Link (Optional)
Connect a separately sold junction box and a portable telephone
(available from Nokia) to control the incoming and outgoing calls of
the portable telephone.
CAUTION
•
Even with hands-free operation, a driver can be distracted
during telephone operation or receiving a call. For the
sake of safety, drivers are requested to refrain from
operating the telephone while driving.
•
For the sake of safety, operations other than incoming
calls and Speed-Dial outgoing calls cannot be used.
• If a portable telephone is connected, its address book, incoming
and outgoing history, short message history and standardized
sentences are downloaded to the junction box.
Please refer to the instruction manual of the junction box.
• When a portable telephone is not connected, “NO PHONE” is
displayed for at least 5 seconds, then the mode returns to the
original source mode.
• When the portable telephone is taken off the junction box during an
incoming or outgoing call, or during a hands-free call, the call will
be treated as an ordinary one by the portable telephone.
• When there is an incoming call while the power of the IVA-D300R/
IVA-D300RB is OFF, the power of the IVA-D300R/IVA-D300RB
turns ON automatically, hands-free call is cut, and the portable
telephone call is enabled.
• Even if the power of the portable telephone is OFF, when IVA-
D300R/IVA-D300RB is set to the telephone mode, the power of the
portable telephone will be turned ON.
• If the ACC power of the vehicle is turned OFF (the engine is
stopped) during a hands-free call, the hands-free call cuts, and the
normal portable telephone call is enabled.
• If there is an incoming call during operation (except an outgoing
call or talking), operation mode will end and switch to the
incoming or talking mode.
• An outgoing call from a portable telephone is also possible.
However, you cannot perform different operations at the same time
from a portable telephone and IVA-D300R/IVA-D300RB as
malfunction can result.
• With a junction box connected outgoing, incoming, and sending
history will also be recorded in the portable telephone.
• While telephoning, Time Correction is set to normal (0.0ms) and
DEFEAT is also set to ON. When the call has finished, the unit
returns to the setting which you previously set.
• The telephone volume can be adjusted from the IVA-D300R/IVA-
D300RB. The volume you set during the call is memorized, and is
automatically applied again on the next call.
Setting the Announcement Select Mode
1
Press and hold
T.INFO/RDS
for at least 2 seconds.
The display changes to the RDS/DAB
*
mode screen.
*
RDS mode screen when DAB is not connected.
2
Touch
[ANNC]
.
3
Touch
[
;
]
or
[
:
]
to select the desired
Announcement.
All Select
→
Traffic News
→
Travel news
→
Warning
→
News
→
Weather
→
Event
→
Special Event
→
Radio Info
→
Sports
News
→
Financial
→
All Select
4
Touch
[ON]
or
[OFF]
to set ON/OFF for the
selected Announcement.
Repeat Steps 3 and 4 to set more.
• When one of the selections between “All Select” and “Financial”
is set to ON, no announcement interruptions are made if you set to
OFF by touching
[ANNC ENT]
.
• If you set ON/OFF with the “All Select” selection, you can set
ON/OFF for the selections from “Traffic News” to “Financial.”
Tips
•
When an urgent broadcast is received, the mode
automatically changes to the DAB mode to receive the
Alarm Announcement. If you adjust the volume level at this
time, that volume level is memorized, and that volume level
is applied the next time you receive an urgent broadcast.
•
If the announcement that you select in Step 3 interrupts, the
selected announcement label is displayed. If you adjust
the volume level at this time, that volume level is
memorized, and that volume level is applied the next time
announcement interrupts.
5
Touch
[RETURN]
to return to the DAB setting
screen.
Changing the Display Mode
You can display information that is sent from broad-casting stations,
such as the channel number or the service name that you are receiving
or listening.
While receiving DAB, touch
[INFO.]
to change the
display mode.
Ensemble Label Display
→
Service Label Display
→
Component Label Display
*
1
→
Dynamic Label (Radio Text)
Display
*
2
→
Ensemble Label Display
*
1
You can display this only when the broadcasting station supplies
the Service Component Label. Otherwise, “No Component” is
displayed.
*
2
“NO TEXT” is displayed when broadcasting stations which
contain no Dynamic Label are received.
• Dynamic Label is not displayed in the dual screen.
