15
-EN
DVD/Video CD
In this section, both remote control and main unit operation are described.
• DVD and Video CD operation can be controlled from both the
remote control and the main unit. In this section, both remote
control and main unit operation are described.
• To view DVD and Video CD, the optional TV monitor is required.
• DVA-9860R automatically changes the video output signal (NTSC
or PAL), according to the disc. To set NTSC or PAL on the
connected monitor, refer to the Owner's Manual of the monitor.
Playing DVD/Video CD
Caution
• Not all functions will operate for every DVD. See the individual
DVD’s instructions for details on the features supported.
• Fingerprints on a disc may adversely affect playback. If a
problem occurs, remove the disc and check for fingerprints on
the playback side. Clean the disc if necessary.
• When using the remote control, be careful to press one button
at time. Pressing multiple buttons at the same time may cause
erroneous operation.
• If you try to perform an invalid operation (based on the type of
disc being played), the following mark is displayed on the
monitor screen:
Play Position Memory Function
Even if you turn power off or switch the Ignition Key to OFF during
playback or change the source, playback will continue from the point
where playback stopped when the power is turned ON again.
1
Insert a disc with the label side facing up.
The disc will be pulled into the unit automatically.
When a disc is already inserted, press
SOURCE/POWER
on the main unit to switch to the DISC mode.
The mode will change every time the button is pressed.
TUNER
→
DISC
→
CD CHANGER
*
→
TUNER
* Only when the CD changer is connected
2
To eject the disc, press
c
on the main unit.
• Do not remove a disc during its eject cycle. Do not load more than
one disc at a time. A malfunction may result from doing either.
• If the disc does not eject, press and hold
c
for at least 2 seconds.
• The reverse side of a double-sided DVD will not be played
automatically. Remove the disc, turn it over, and reinsert it.
• Never insert map discs for navigation purposes as they could
damage the equipment.
• Refer also to “DVD Setup” (pages 25 to 27).
If a menu screen appears
On DVDs and video CDs with playback control (PBC), menu screens
may appear automatically. If this happens, perform the operation
described below to start playback.
• This operation is controlled using the remote control unit.
• For many discs, the menu screen can also be displayed by pressing
MENU
.
DVD menu
Press
8
,
9
,
;
or
:
to select the desired item, then
press
ENT.
• For some discs it is possible to select items directly from the menu
screen using the
number keys
(“0” to “9”).
Video CD menu
Use the
number keys
(“0” to “9”) to select the desired
number, then press
ENT.
• The menu screen does not appear when the PBC function is turned
off. In this case, set VCD PLAY MODE to turn on the PBC
function. For details, refer to “Setting the Video CD Play Mode”
(page 28).
Stopping Playback (PRE-STOP)
Press
L
during playback to stop playback. That position is stored in
memory.
1
During playback, press
L
on the remote control
unit.
“PRE-STOP” is displayed.
2
Press
-
/
J
in the PRE-STOP mode.
Playback starts from the position at which it was stopped.
• For some discs, the position at which playback was stopped may
not be accurate.
RETURN
:
/
J
g
L
CLR
DISP/TOP M.
AUDIO
;
8
:
ENT.
9
f
number
keys
(0 to 9)
ANGLE
SUBTITLE
g
f
Rotary encoder
-
/
J
SEARCH/Q.S.
c
4(
)
MENU
SOURCE/
POWER
Summary of Contents for DVA-9860R
Page 64: ......
