37
-EN
If MUSIC MODE is selected, the centre width can be adjusted
with following operations.
This function offers the optimum vocal position by adjusting
the centre channel position between the centre speaker and
the L/R speaker. (The adjustments established in “Adjusting
the acoustic image” (page 35) are ineffective while this
function is activated.)
1) Select CTW_CONT ON/OFF by turning and then
pressing the
Rotar y encoder
.
If ON is set, you can enjoy the optimum vocal position
by distributing the centre channel sound between the
centre speaker and L/R speaker.
2) Adjust the level (LEVEL) by turning and then pressing
the
Rotar y encoder
.
The level can be adjusted between 0 to 7. When the
level increases, the centre channel position moves from
the centre speaker position to both sides.
5
When the setting is complete, pr
ess and hold
CENTER f.
for at least 2 seconds.
The unit returns to the normal mode.
Press
CENTER f.
to select another item to be set.
• This adjustment is effective when the setting of the centre speaker
is SMALL or LARGE in the speaker setup settings.
• Avoid stopping, pausing, switching the disc, cueing, fast-
forwarding or switching the audio channel of this unit while
making this adjustment. The setting is cancelled if the Decode
mode is switched.
• This adjustment is ineffective when the speaker is set to CENTER
OFF in “Setting the Speakers” (page 30).
• This function only works with two-channel signals. This operation
is ineffective when 5.1-channel DTS or Dolby Digital signals are
input.
• If the setting of REAR FILL is made when REAR MIX is ON, sound
is unchanged in the rear fill setting because REAR MIX is given
priority during 2 channel decoder other than linear PCM.
• For linear PCM signals, the voice is output from the rear speaker
regardless of the REAR FILL and REAR MIX setting.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 37.
Linear PCM Setting
The output when playing discs recorded in linear PCM can be set to 2
or 3 channels.
1
Check that Defeat mode is of
f (page 19).
2
Press and hold
CENTER f.
for at least 2 seconds.
The audio processor control mode is activated.
3
Select the PCM mode by pr
essing
CENTER f.
repeatedly .
4
Select 2 CH or 3 CH by tur
ning and then the
Rotary encoder
.
2CH:
2ch output (L/R)
3CH:
3ch output (L/R/CENTER)
5
When the setting is complete, pr
ess and hold
CENTER f.
for at least 2 seconds.
The unit returns to the normal mode.
Press
CENTER f.
to select another item to be set.
• This adjustment is ineffective when the speaker is set to CENTER
OFF in “Setting the Speakers” (page 30).
Storing Settings in the Memory
Up to 6 set and adjusted contents can be stored on the unit.
All that are setting and adjusting items described below are stored in
one preset memory.
1
Adjust and set the value to be stor
ed.
2
Press and hold for at least 2 seconds any one of
the
preset buttons (1 through 6)
into which you
want to stor e the set/adjusted value as pr
eset
memor y (MEMOR Y 1 thr ough MEMOR Y 6).
• This function is operable only when Defeat is set to OFF.
• The stored contents will not be deleted even when battery power
cord is detached.
Getting out the Preset Memory
1
Check that Defeat mode is of
f (page 19).
2
Press and hold
CENTER f.
for at least 2 seconds.
The audio processor control mode is activated.
3
Select the mode to be set by pr
essing
CENTER f.
repeatedly .
4
Press any one of the buttons to select the pr
eset
memor y (MEMOR Y 1 thr ough MEMOR Y 6) you want
to recall.
It takes a few moment to get out the preset memory.
30
31, 32, 34
32, 33
30
30
34
36, 37
35
37
Setting the Speakers
Setting Time Correction/Switching Phase/
Setting the Bass Focus
Adjusting EQ
Adjusting X-OVER
Setting MX
Setting BASS COMP.
Setting PRO LOGIC II/Adjusting the
Centre Width
*
Adjusting Dolby Surround
*
Linear PCM Setting
*
Refer to page
Setting/adjusting items
* Depending on the input signal, sound effect may not be obtained.
Summary of Contents for DVA-9860R
Page 64: ......
