Alpine DVA-9860R, Owner'S Manual

Page: 33 / 64

32
-EN
Graphic Equalizer Adjustments
The graphic equalizer allows you to modify the sound using 31 bands
each for the front (left and right), rear (left and right) and centre
speakers. An additional 10 bands are available for the subwoofer. This
allows you to customize the sound to suit your taste.
1
Check that Defeat mode is of f (page 19).
2
Press and hold CENTER f. for at least 2 seconds.
The audio processor control mode is activated.
3
Select the G-EQ mode by pr essing CENTER f.
repeatedly .
4
Select L+R or L/R by pr essing and holding BAND
for at least 2 seconds.
L+R: Sets the same adjustment values for the left and
right channels.
L/R: Different adjustment values can be set for the left
and right channels.
When parametric EQ is adjusted, this setting will be
turned off.
5
Select the desir ed channel by pr essing
g
or
f .
When L+R is selected :
FRONT
→
REAR
→
CENTER
→
SUBWOOFER
→
FRONT
When L/R is selected :
FRONT L
→
FRONT R
→
REAR L
→
REAR R
→
CENTER
→
SUBWOOFER
→
FRONT L
• The speakers display differs, depending on the connected speakers.
6
Select the fr equency by tur ning and then pr essing
the Rotary encoder .
Adjustab le frequenc y :
FRONT/REAR/CENTER : 20Hz - 20kHz (in 1/3 octave
steps)
SUBWOOFER : 20Hz - 160Hz (in 1/3 octave
steps)
7
Adjust the level (LEVEL) (±9dB 1dB step) by
tur ning and then pr
essing the
Rotary encoder
.
8
To adjust other channels, r epeat steps 5 to 7.
9
When the setting is complete, pr ess and hold
CENTER f. for at least 2 seconds.
The unit returns to the normal mode.
Press
CENTER f. to select another item to be set.
• When the speaker is set to the “OFF” mode, the level of the
graphic equalizer for that speaker cannot be adjusted. Refer to
“Setting the Speakers” (page 30).
• Check the playable frequency ranges of the connected speakers
before making the equalizer adjustments. If the speaker’s playable
frequency range is 55 Hz to 30 kHz, for example, adjusting the
40 Hz or 20 Hz band has no effect. Additionally, you may overload
and damage the speakers.
• When graphic EQ is adjusted, the adjustment for parametric EQ
becomes ineffective.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 37.
8
Select the desir ed channel by pr essing g or
f
.
When L+R is selected :
FRONT 1
→
FRONT 2
→
REAR
→
CENTER
→
SUBWOOFER
→
FRONT 1
When L/R is selected :
FRONT 1L
→
FRONT 1R
→
FRONT 2L
→
FRONT 2R
→
REAR L
→
REAR R
→
CENTER
→
SUBWOOFER
→
FRONT 1L
• The speakers display differs, depending on the connected speakers.
9
Adjust the calculated time cor rection value (0.00 to
20.00ms) by tur ning and then pr essing the
Rotary
encoder .
Switching the Phase
10
Switch the phase (PHASE) by tur ning and then
pressing the Rotary encoder .
11
To adjust other channels, r epeat steps 8 to 10.
12
When the setting is complete, pr ess and hold
CENTER f. for at least 2 seconds.
The unit returns to the normal mode.
Press
CENTER f. to select another item to be set.
• When the speaker is set to the “OFF” mode, the TCR for that
speaker cannot be set. Refer to “Setting the Speakers” (page 30).
• The adjustment value for FRONT2 (Speakers) which is adjusted in
time correction, is also applied to the front speakers in “Setting
Bass Focus” (page 34).
• The adjustment (AUTO TCR) cannot be automatically set on this
unit.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 37.