Allnet ALL-NAS1000 User Manual Download

Page: 87 / 137

A description of each item follows:

LDAP Support

Item

Description

LDAP Service

Enable or Disable LDAP service.

LDAP Server IP

Input LDAP server IP address.

Base Domain

Input base domain information ex. dc=tuned, dc=com, dc=tw

Manager

Input manager’s name.

Password

Input manager’s passowrd

Apply

Click Apply to save your changes.

Check ObjectClass

Click this checkbox to ensure LDAP server having Samba sam and
POSIX account or it may not working properly for LDAP client
authentication.

Network Service

Use the Network Service menu to make network service support settings.

Samba / CIFS

There are options is currently allow Admin to Enable/Disable to operate ALLNET IP
storage associated with Samba / CIFS protocol. With the option changed, it will
need to reboot system to activate.

Samba Service

Summary of Contents for ALL-NAS1000










































































































































Search results

Summary of Contents for ALL-NAS1000

Reviews:

Related manuals for ALL-NAS1000

Brands by name

Popular brands

Allnet ALL-NAS1000, User Manual

Search results

Summary of Contents for ALL-NAS1000

Reviews:

Related manuals for ALL-NAS1000

Brands by name

Popular brands