Allnet ALL-NAS1000 User Manual Download

Page: 79 / 137

A description of each item follows:

ADS/NT Support

Item

Description

Work Group / Domain
Name

Specifies the SMB/CIFS Work Group / ADS Domain Name (e.g.
MYGROUP).

ADS Support

Select Disable to disable authentication through Windows Active
Directory Server.

ADS Server Name

Specifies the ADS server name (e.g. adservername).

ADS Realm

Specifies the ADS realm (e.g. example.com).

Administrator ID

Enter the administrators ID of Windows Active Directory, which is
required for ALLNET IP storage to join domain.

Administrator
Password

Enter the ADS Administrator password.

Apply

To save your settings.

To join an AD domain, you can refer
the figure and use the example below
to configure the ALLNET IP storage for
associated filed input:

AD Domain Example
Item

Information

Work Group / Domain
Name

domain

ADS Support

Enable

Summary of Contents for ALL-NAS1000










































































































































Search results

Summary of Contents for ALL-NAS1000

Reviews:

Related manuals for ALL-NAS1000

Brands by name

Popular brands

Allnet ALL-NAS1000, User Manual

Search results

Summary of Contents for ALL-NAS1000

Reviews:

Related manuals for ALL-NAS1000

Brands by name

Popular brands