Allnet ALL-NAS1000 User Manual Download | Manualshive

Page: 61 / 137

background image

61

After your changes have been made, click Apply to confirm any modifications.
Once changes are applied, the associated information will be updated on the Stack
Target List window.

D. Stack Target ACL

If the stack target Public setting set to Yes, then the ACL button will be grayed out.
However, if Public setting is set to No, then the ACL button will be available for
you to setup user access permissions for the stack target.

ACL settings will be exactly the same as system folder that you may have setup
previously.

E. Reconnect a Stack Target
The enabled stack target devices may be disconnected by situations such as power
outages or network disconnects. When this happens, the Reconnect button will
available. To attempt to reconnect the stack target, click Reconnect.

«
...
59
60
61
62
63
...
»

Summary of Contents for ALL-NAS1000










































































































































Reviews:

No comments

Related manuals for ALL-NAS1000

Brand: G-Technology Pages: 32

Brand: G-Technology Pages: 35

Brand: Planet Pages: 20

Brand: trueCall Pages: 16

RouterBOARD Groove

Brand: MikroTik Pages: 4

Brand: Lancom Pages: 102

Brand: Stardom Pages: 2

IronKey EMS H350 Enterprise

Brand: DataLocker Pages: 23

Sun Fire X2100 M2

Brand: Sun Microsystems Pages: 128

ApplianceStor 15MT

Brand: Rasilient Pages: 30

Mobile Wi-Fi Pocket Drive

Brand: Macally Pages: 71

Brand: Artesyn Pages: 190

Brand: dallmeier Pages: 32

OmniTik UPA-5HnD

Brand: RouterBOARD Pages: 4

Brand: QNAP Pages: 68

220-420LTO - QUICK

Brand: TANDBERG Pages: 8

xSeries 440 8687

Brand: IBM Pages: 80

xSeries 230 6RY

Brand: IBM Pages: 194

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands