Alcatel IPUP A100 Instruction Manual Download Page 72

Page: 72 / 115

C 51

4 / 4

Alcatel Vacuum Technology France --- IPUP A100 Instruction manual

Monitoring system function table

IPUP A100L version

MANAGEMENT MENU, OPERATING TIME, LAST TEN WARNINGS, LAST TEN HAZARDS

SET

ENTER

Initial configura-

tion

ENTER

MANAGEMENT

PASSWORD

0 to 65535

MANAGEMENT

VERSION

FRAME SERIAL N°
M40 SERIAL N°
M40 OTP VERSION
M40 FLASH VERSION
ADP 100 SERIAL N°
OTP DISP. VERSION
FLASH DISP. VERSION

STORAGE

ENABLED/DIS-

ABLED

DIS-

ABLED

CONFIG SAVE

Save the pump configuration into the remote display

memory. Valid by pressing Enter Key.

CONFIG LOAD

Allow to transfer the remote display memory into the

pump memory. Valid by pressing Enter Key.

OPERATING TIME

Displays the operating times of the various components.

LAST WARNING(S)

Displays the 10 last recorded warnings.

LAST ALARM(S)

Displays the 10 last recorded hazards.

Summary of Contents for IPUP A100




















































































































Search results

Summary of Contents for IPUP A100

Reviews:

Alcatel IPUP A100, Instruction Manual, Page: 72 / 115

Search results

Summary of Contents for IPUP A100

Reviews: