manualshive.com logo in svg

Albatron KI690-AM2, User Manual, Page: 63 / 64

Share
Download
Albatron KI690-AM2 User Manual Download Page 63

 
 
 
 
 

Mainboard KI690-AM2 

 59 

Install Windows

®

 Vista/ Windows

®

 XP OS onto your RAID HDDs 

 

This section will explain how to install Windows

®

 Vista/ Windows

®

 XP operating system onto 

your RAID drives. The installation steps below will assume that your HDDs have already been 

attached to the SATA connectors, and your RAID arrays have already been configured using 
the ATI RAID Utility (ATI RAID Utility Configuration section). 

 
 
 

Preparation for Windows

®

 Vista:

 Before installing the OS, copy the “RAID Driver” files from 

the bundled CD onto media that you can use on an existing storage device on your computer 
(floppy disk drive, USB ThumbDisk, CD, or DVD).   

 
 

The files are located on the CD-ROM as follows: 

   

Windows

®

 Vista 32 bit

：

CD-ROM => \ Driver \ RAID \ VISTA \ LH \ *.* 

 

 Windows

®

 Vista 64 bit

：

CD-ROM => \ Driver \ RAID \ VISTA \ LH64A \ *.* 

 
 

Preparation for Windows

®

 XP:

 Before installing the OS, copy the “RAID Driver” files from the 

bundled CD onto media that you can use on an existing storage device on your computer (e.q. 

floppy disk drive).   

 
 

The files are located on the CD-ROM as follows: 

 

Windows

®

 XP 32 bit

：

CD-ROM => \ Driver \ RAID \ XP \ x86 \ *.* 

 

 Windows

®

 XP 64 bit

：

CD-ROM => \ Driver \ RAID \ XP \ x64 \ *.* 

 
 
 

※

  This will have to be done on another system if you are installing the system from scratch. 

 
 
 
 
 

Install Windows

®

 Vista: 

 
 

1.  During a Windows

®

 Vista installation, there will be an item “Load Driver”. Click on it and 

then insert the media containing the RAID Driver files into your computer.   

 

2.  Click on “Browse” to browse into the folders of the media to locate the folder with the files.. 

 

3.  Once you have located the folder, click on “OK” to load the RAID Drivers. The system will 

scan for the driver automatically. When you see the file “ATI AHCI Compatible RAID 

Controller” display on the screen. Press “Next” to continue. 

 

4.  You will return to the “Install Windows” screen to continue with the installation. Follow the 

setup instructions and select the partition where you want to install operating system files. 

 

5.  After setup examines your disks, it will copy files to the Windows

®

 Vista installation folders 

and restart the system. After the system is rebooted, the setup program will continue with 

the installation all the way to completion. 

 

6. Wait 

until 

Windows

®

 Vista finishes installing devices, regional settings, networking settings, 

components, and any other remaining tasks. Reboot the system if you are asked to do so. 

 
 

Summary of Contents for KI690-AM2

































































Reviews:

No comments