Albatron KI690-AM2 User Manual Download Page 11

Page: 11 / 64

Mainboard KI690-AM2

FAN Headers: CPUFAN, AUXFAN

There are two fan headers available for cooling fans. These cooling fans play an important role

in maintaining ambient temperatures in your system. The CPUFAN header is attached with a
CPU cooling fan. The AUXFAN header is attached with another cooling fan.

Pin

Assignment

1 Ground
2 Power

(+12V)

FAN RPM rate sense

CPUFAN

Smart Fan Control

Pin

Assignment

1 Ground
2 Power

(+12V)

AUXFAN

FAN RPM rate sense

Memory Installation: DDRII1/2

The KI690-AM2 provides two DDRII SO-DIMM sockets with Dual Channel Technology

supported. These two sockets allow you to install 200-pin, non-ECC & unbuffered DDR II 667/

533/ 400 SO-DIMMs, supporting to install a total memory capacity of 2 GB.

Attention

You can avoid damaging your CPU due to high temperatures with

proper cooling equipment. It is recommended that attach a cooling fan

on top of your CPU. Use the

CPUFAN

header to attach the fan cord.

On most fan power cord, the black wire of the fan cable is the “ground”

and should be attached to pin-1 of the header.

Summary of Contents for KI690-AM2

































































Search results

Summary of Contents for KI690-AM2

Reviews:

Albatron KI690-AM2, User Manual, Page: 11 / 64

Search results

Summary of Contents for KI690-AM2

Reviews: