Albatron KI690-AM2 User Manual Download Page 38 | Manualshive

Page: 38 / 64

Albatron KI690-AM2 User Manual Download Page 38

Mainboard KI690-AM2

34

Chapter 3: Software Setup

Software List

Software Installation

Place the Driver CD into the CD-ROM drive and the Installation Utility will auto-run. You can

also launch the Driver CD Installation Utility manually by executing the Intel.exe program
located on the Driver CD. (For more details, please refer to the Readme.txt files that in each

folder of the Driver.)

1. When you insert the driver CD into the CD ROM, you’ll see the screen as the picture below.

There are several buttons displayed in the main screen as shown below.

Category

Platform

AMD

®

Chipset Driver

Windows Vista /XP

Realtek

®

Audio Driver

Windows Vista /XP

RAID Utility

Windows Vista /XP

Marvell

®

Lan Driver

Windows XP

HDMI Audio Driver

Windows XP

Microsoft

®

DirectX 9.0c

Windows XP

◎

The pictures shown below are for your reference only. The version of the software you
received and shown on the screen may vary depending on models.

Attention

Your system must be using Windows

®

XP with Service Pack 2 or

higher (this is necessary when installing the AMD Chipset Driver).

«
...
36
37
38
39
40
...
»

Summary of Contents for KI690-AM2

































































Reviews:

No comments