manualshive.com logo in svg

Albatron KI690-AM2, User Manual, Page: 48 / 64

Share
Download
Albatron KI690-AM2 User Manual Download Page 48

 
 
 
 
 

Mainboard KI690-AM2 

 44 

2.  The option for enabling RAID will be found on the “Peripherals” screen. On this screen, 

arrow down to the “South OnChip IDE Device” as shown below. Press <Enter> which will 

take you to a submenu. Arrow down to the “ATI SATA Type” item.    Then press <Enter> 
again to access the next submenu. Arrow down to the “RAID” item and press <Enter>. 

 
 

Peripherals >> South OnChip IDE Device >> ATI SATA Type >> RAID 

 
 
 

After you complete the instructions above, save the settings and exit the BIOS Setup Utility 

(SAVE to CMOS and EXIT). 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

ATI RAID Utility Configuration 

 

The ATI RAID Utility is used to configure RAID disk management into your hard disks. This 

section will explain how to setup and maintain your RAID disk drives.   

 

Summary of Contents for KI690-AM2

































































Reviews:

No comments