manualshive.com logo in svg

Albatron KI690-AM2, User Manual, Page: 58 / 64

Share
Download
Albatron KI690-AM2 User Manual Download Page 58

 
 
 
 
 

Mainboard KI690-AM2 

 54 

Rebuilding a Logical Drive on a Mirrored Array 

 

This section explains the process of replacing a failed drive that was part of a Mirrored array.   

The replacement drive will be rebuilt by reconstructing the data from an existing Mirrored drive. 
This function only applies to the disk drives with redundancy, namely RAID 1 and RAID 0+1.   

 
 
 
 

Before Rebuilding the Logical Drive: 

 
 

1.  Before you begin rebuilding a logical drive, you must install the “RAID Utility” from the 

bundled CD. Please insert the bundled CD and click on the “RAID Utility” to install it.   

 
 

         

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 

2.  When the installation is done, there will be a shortcut titled “WebPAM” on the desktop. 

Double click on it to start the program. 

 
 

Windows XP

Windows Vista

Summary of Contents for KI690-AM2

































































Reviews:

No comments