manualshive.com logo in svg

Albatron KI690-AM2, User Manual, Page: 26 / 64

Share
Download
Albatron KI690-AM2 User Manual Download Page 26

 
 
 
 
 

Mainboard KI690-AM2 

 22 

Advanced BIOS Features 

 
 

 

 
 

Hard Disk Boot Priority 

 

Select hard disk drive boot priority. 

 

CD-ROM Boot Priority 

 

Select CD-ROM boot priority when you plug a CD-ROM drive onto your system.   

 

First /Second/Third Boot Device 

 

Select the order in which devices will be searched in order to find a boot device. 
Options: Removable (Default for first boot device), CDROM (Default for second boot device), 

Hard Disk (Default for third boot device), Disabled. 

 

Boot Other Device 

 

This setting allows the system to try to boot from other devices if the system fails to boot from 

the 1st/ 2nd/ 3rd boot devices. Options: Enabled (Default), Disabled. 

 
 

Advanced BIOS Features 

Virus Warning 

 

This option allows you to choose the Virus Warning feature for IDE Hard Disk boot sector 

protection. If this function is enabled and a program attempts to write data into this area, BIOS 

will display a warning message on the screen and sound an audio alarm (beep). 
Options: Disabled (Default), Enabled. 

Summary of Contents for KI690-AM2

































































Reviews:

No comments