background image

41

At the last stage, rise the boiler to standing position while turning around the lower and back (wall 

side) edge of the boiler. Do not forget to position a support member like a wooden block under and 

between with the bottom and front side of the boiler and the floor.

3.2. Unpacking The Boiler

The carton material used in your product’s package is fully recycleable. It is advised to unpack your 

product just before installation. 

Alarko Carrier is out of responsibilty due to damage or defects 

emerging from inappropriate conditions of storage. 
The  packing  material  (plastics,  foam,  polystrene,  nails,  screws,  bolts  or  staples/punches 

etc.) should always be kept far from childs’ reach.

ALDENS condensing boiler is attached as unable to shake or move on a wooden palette.
The ALDENS 65-85-105-130-150 L/T boilers’ (master or slave)  net weights are 55, 69, 69, 75 and 

89 kg’s in order as unpacked initially. 

Do not try to rise or levitate by your own!

Apply for help to at least one more person. It is advised to use an equipment like a lift in order to 

rise and hang the boiler to a wall or a carrier structure. Follow the steps below to unpack and rise 

the boiler.

Summary of Contents for ALDENS 105













































































Reviews: