background image

Failure to install this AKW product in accordance with supplied instructions or the making of 

unauthorised modifications will invalidate any warranty and will affect product safety.

Post

 AKW, Pointon Way, Hampton Lovett,     
 Droitwich Spa, WR9 0LR

Contact Information

Orderline 

01905 823299

General Enquires

01905 823298

Technical Help line

01905 823242 

Fax

01905 823297

Website

www.akw-ltd.co.uk

Enquires email

[email protected]

Quotes & orders email

[email protected]

DANGER

 

OF

 

DEATH! 

230V AC 

Lethal Voltage present on the AC 
supply to the pump inner case. 
This unit must be connected to 
a double-pole switched supply, 
suitably fused and provided with a 
RCD protection.

This product must be 
installed by a qualified and 
competent electrician and 

in accordance with the current 
edition of the Wiring Regulations 
BS7671. This appliance must be 
located to comply with the safety 
zones as defined in the wiring 
regulations. 

Isolate this unit before access for 
maintenance or any other purpose.
Do not immerse in water.

No USER serviceable parts within 
case. 

The cover must only be removed 
by an authorised service person or 
electrician.

Important 
Safety 
Information

© 2012 AKW   

 

         

 

   

                               07-001-196-01

Summary of Contents for M11 DigiPump





















Reviews: