Akw M11 DigiPump Installation And User Care Instructions Download Page 18

Page: 18 / 20

Warranty Registration Details

To be completed by Installer

INSTALLED ON

______

_______

INSTALLED BY

_______________________________________________

ADDRESS

____________________________________________________

CONTACT

____________________________________________________

Product Identification label can be found on the pump case and also on the outer
packaging.

Model / Part Number

__________________________________________

Serial Number (SN)

____________________________________

Batch Number (BN)

___________________________________________

IMPORTANT: TO ACTIVATE YOUR WARRANTY PERIOD

YOU MUST REGISTER YOUR PRODUCT WITHIN 30 DAYS!

FREE 5-YEAR WARRANTY OFFER

To register for your free 5 year warranty please return

the registration card within 30 days of installation.

Registration is optional but you will only receive this

5-year extended warranty if you register.

Your statutory rights are not affected

Please complete the registration card within 30 days and return to us in the prepaid envelope for your Free Warranty to start.

Product Identification label

Summary of Contents for M11 DigiPump





















Search results

Summary of Contents for M11 DigiPump

Reviews:

Related manuals for M11 DigiPump

Brands by name

Popular brands

Akw M11 DigiPump, Installation And User Care Instructions

Search results

Summary of Contents for M11 DigiPump

Reviews:

Related manuals for M11 DigiPump

Brands by name

Popular brands