background image

3516526A02 Ed. 01

6

Keypad

Press and hold for 3 seconds to activate/deactivate the Stand-By mode. In this mode, regulation is 
paused and the 

m

 icon is displayed..

In the programming menu, it exits the parameter without saving changes and returns to the previous 
level, or exits programming.

Pressing once without holding displays the temperature of sensor S2 for 10 seconds (if it is enabled).
Pressing it for 3 seconds starts/stops the defrost.
In the programming menu, it allows you to scroll through the different levels, or when setting a 
parameter to change its value.

A brief press shows the SELFDRIVE mode errors.
Pressing it for 3 seconds activates/deactivates the continuous cycle mode.
In the programming menu, it allows you to scroll through the different levels, or when setting a 
parameter to change its value.

Pressing once without holding activates/deactivates the cold room light.
Pressing it for 3 seconds accesses the condensed programming menu.
Pressing it for 6 seconds accesses the expanded programming menu.
In the programming menu, it accesses the level shown on the display or, during the setting of a 
parameter, accepts the new value.

Pressing it once without holding it down displays the current effective value of the temperature Set 
Point in the upper display and the superheating set point in the lower display, taking into considera-
tion temporary changes due to other parameters.
When an alarm is in progress, pressing once without holding mutes the acoustic alarm.
Pressing for 3 seconds accesses the temperature Set Point setting.

STAND-BY

If the regulation cannot be stopped immediately due to its configuration, a controlled stop process starts
and the m icon flashes. To stop the controlled stop process and force Stand-by, press the Stand-by key 
again for 3 seconds.

Summary of Contents for 16526A













































Reviews: