manualshive.com logo in svg

AJA Ki PRO ULTRA, Installation & Operation Manual

Share
Download
AJA Ki PRO ULTRA Installation & Operation Manual Download Page 29

Ki Pro Ultra   v1.2r1

www.aja.com

29

 

Chapter 4: Front Panel Operation

Overview

There are two ways to control Ki Pro Ultra—from the front panel or remotely from a web 
browser connected via the Ethernet RJ45 connector. (See 

“Browser Remote Control” on 

page 60

.) This chapter discusses controlling and using Ki Pro Ultra from its front panel.

Chapter 2 described the panel controls overall, so you may want to read and understand 
that material first. This chapter describes each of the front panel's modes and the various 
menu parameters.

Control Panel Operation

There are two basic front panel modes:

• Transport (default mode) – 

PLAY, STOP, FFWD, REV, REC.

 These functions are active at 

all times. By default the unit starts in a “record standby” or “transport idle” state.

• Display – when you press the display button, an overlay is placed on the LCD screen. 

When you push one of the remaining menu buttons (

Status

, 

Config

, or 

Media

) Ki Pro 

Ultra will display:

• Status/Alarm reports

• Configuration menus

• Media formatting operations

Display Button Sequence:

Press the Display button twice to bring up audio VU meters. Pressing a third time brings up the 
last menu selected. Press again to turn the overlay off.

Summary of Contents for Ki PRO ULTRA



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands