background image

 

Page 

3

 of 

14

 

 

3

 

Extra equipment you could consider for your new inflatable: 

  Ground sheet to protect the underside of your inflatable 

  Sandbag covers to anchor your inflatable indoors 

  Sack truck to move your inflatable safely 

  RCD to attach to your extension lead 

  Crash Mats 

 

This inflatable can be set up and packed away by 3 persons who have 
had proper manual handling training and use the correct equipment to 
move the inflatable. 

             

 

 

3.  Intended use of the product: 

  

 

 

 

 

 

 

 

 

 

 

                    

 

 

4.  Operating guidelines: 

-  Before entering the game area, 

CLEAR INSTRUCTIONS SHALL BE GIVEN

 to players 

on their conduct during playtime: 

NO SOMERSAULTS 

or

 

any

 ACROBATICS 

allowed. 

-  All players remove footwear, eye wear, cell phones, keys, neck wear and/or any 

sharp items. 

DO NOT 

allow the users to 

OBSTRUCT THE MOVEMENT OF THE ARM

. This 

includes no hanging on the arms, pushing-pulling them. 

-  For safety reasons, users should only stand at the designated jumping space 

(numbers, podiums). Do not allow them to get closer to the middle of the bed. 

-  No one with 

ANY PRE-EXISTING INJURIES OR HEALTH CONCERNS 

may 

us

e the “Last One Standing” game. 

-  Every time a user falls 

THE MECHANISM MUST BE STOPPED!

 

-  Use the Emergency Button only in a case of an emergency. After releasing it, 

WAIT AT 

LEAST 5 SECONDS 

before pressing any other button on the Control Box. 

-  The 

MAXIMUM NUMBER OF USERS HAS TO BE RESPECTED 

at all times. 

-  The unit should 

NOT TO BE USED IF IT BECOMES WET

. In the event of rain, the unit 

should be deflated and folded to prevent water collecting on it. 

-  The  Last  One Standing  with  a  single  arm  mechanism  is 

designed to be used by up to eight players and one operator. The 
players must bounce at the right time to avoid the rotating sealed 
arm. The operator has control (via the supplied control box) over 
the speed and direction of the arm to make the game harder or 
easier  as  required.  If  a  user  is  knocked  over  by  the  arm,  they 
should  exit  the  game.  The  operator  must  stop  the  mechanism 
until  the  eliminated  player  has  exited  the  inflatable.  The  last 
player standing is the winner.

 

 

Summary of Contents for Last One Standing















Reviews: