AirLinkWiFi UltraSky CPE2 User Manual Download Page 53

Page: 53 / 62

Default Policy -- The packet that don't match with any rules would be

You can choose to dropped and accepted, default is

Dropped.

MAC/IP/Port Filter Settings

Source MAC Address

: the physical address of the matched data packets

Dest IP Address

: destination IP address of the data packets.

Source IP Address

: IP address of data packet sender.

Protocol

: Protocol type of data packets.

Dest Port Range

: the data packets with their destination ports within the

range will be matched.

Source Port Range

: the data packets with their source port within the range

will be matched

Action

: the data packets that satisfy all above characteristics will be received or

discarded.
If you have changed the above settings, click “

Apply”

button Apply Settings.

4.4.2 Port Forwarding

You may setup Virtual Servers to provide services on Internet.
TCP or UDP packets received by extranet network in the port range are
forwarded to a specific Intranet IP.

Summary of Contents for UltraSky CPE2































































Search results

Summary of Contents for UltraSky CPE2

Reviews:

Related manuals for UltraSky CPE2

Brands by name

Popular brands

AirLinkWiFi UltraSky CPE2, User Manual

Search results

Summary of Contents for UltraSky CPE2

Reviews:

Related manuals for UltraSky CPE2

Brands by name

Popular brands