AirLinkWiFi UltraSky CPE2 User Manual Download Page 46 | Manualshive

Page: 46 / 62

background image

46

/

62

1. Wireless Network
Radio On/Off

: open and close the Wireless Network.

Network Mode

: you can select as below:

11b only

: 11b mode, rate is 11 Mbps.

11g only

: 11g mode, rate is 54 Mbps.

11b/g mixed mode

: 11b/g mixed mode, rate is 11 Mbps and 54 Mbps.

11b/g/n mixed mode

: 11b/g/n mode, rate is 11 Mbps,54 Mbps,150

Mbps/300Mbps.

Other mode can’t be used.

Network Name(SSID)

:Wireless LAN status authentication name ,User can

access the wireless networking through status authentication name only.

«
...
44
45
46
47
48
...
»

Summary of Contents for UltraSky CPE2































































Reviews:

No comments

Related manuals for UltraSky CPE2

Brand: Qongle Pages: 13

Brand: Watchguard Pages: 26

Brand: Tenda Pages: 57

Brand: H3C Pages: 27

TL-WR541G - Wireless Router

Brand: TP-Link Pages: 91

Brand: G2 Pages: 22

DECT 1615 Series

Brand: Uniden Pages: 28

Brand: Youwon Pages: 4

Brand: Z-Com Pages: 18

Infinity ZIP 500

Brand: Harman Pages: 7

WAP11 - Instant Wireless Network Access Point

Brand: Linksys Pages: 33

Brand: Huawei Pages: 117

Brand: Huawei Pages: 24

Brand: Huawei Pages: 122

Brand: Huawei Pages: 78

Brand: Huawei Pages: 25

Brand: Huawei Pages: 172

Brand: Huawei Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands