AirLinkWiFi UltraSky CPE2 User Manual Download Page 25 | Manualshive

Page: 25 / 62

background image

25

/

62

2.5.2 Upload Firmware

Upgrade the new firmware to obtain new functionality.

It takes about 1 minute to upload upgrade flash and be patient please.
Caution! A corrupted image will hang up the system.

Update Firmware

: upgrade the system software of the AP. Select the correct

upgrade file and Click “

Apply

” .

2.5.3 Settings Management

You might save system settings by exporting them to a configuration file,
restore them by importing the file, or reset them to factory default.

Export Settings

: store the configuration file locally for later recovery.

«
...
23
24
25
26
27
...
»

Summary of Contents for UltraSky CPE2































































Reviews:

No comments

Related manuals for UltraSky CPE2

tm-g5240 - T-mobile Hotspot Wireless

Brand: T-Mobile Pages: 2

Brand: Ubiquiti Pages: 24

UniFi AP AC Outdoor

Brand: Ubiquiti Pages: 26

Skyr@cer USB 4101GMR

Brand: Topcom Pages: 212

Brand: Shenzhen Hongdian Technologies Pages: 135

Brand: Tenda Pages: 30

Brand: EE Pages: 2

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 19

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 22

Brand: Panasonic Pages: 22

Brand: Panasonic Pages: 21

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 22

Brand: Panasonic Pages: 26

Brand: Panasonic Pages: 25

Brand: Panasonic Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands