manualshive.com logo in svg

Aim-TTI TGR2050 Series, Instruction Manual

Share
Download
Aim-TTI TGR2050 Series Instruction Manual Download Page 81

14 - Stores menu   

Copying files 

   

 

80    

 

 TGR2050 Series Instruction Manual 

Copying files 

Copying an internal file to an external flash drive 

To copy a file from the internal memory to an external flash drive, firstly, make sure 

the flash drive is inserted and recognised; indicated by the symbol in the status bar: 
 
Select the 

File Location

 parameter window, select 

Internal

 and touch

 OK

.  

Select the file to be copied using the 

↑ ↓

 arrow keys. 

To copy the file, touch 

File Ops. 

This will bring up the file options menu.

 

 Here files can be copied, deleted or renamed. To copy the file, touch 

Copy

. 

The copy menu allows files to be copied to both internal memory and an external 

flash drive. Select the 

Drive 

parameter window, select 

External

 and touch 

OK

. 

The file can now be re-named and copied.  
Select the 

File

 parameter window, type in the file name using the on-screen keypad 

and touch 

OK

. Touch 

Copy

 to copy the file, the file is now stored on the external 

flash drive. 
To copy all of the selected file type, touch

 Copy All

. The file name will remain the 

same when all files are copied. 

Summary of Contents for TGR2050 Series





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands