Aim-TTI TGR2050 Series Instruction Manual Download Page 16

Page: 16 / 100

7 - Getting Started

Status bar details

TGR2050 Series Instruction Manual

Status bar details

①

-Reference clock status

If the internal clock is being used,

INT REF

is displayed in the status bar.

If an external clock is being used,

EXT REF

is displayed in the status bar.

See ‘Reference clock source’ for more details on how to set the clock source.

②

-Print screen

When the print screen function is activated and a print screen is being captured,

PRT SCRN

will appear in the status bar. For more details on print screen, see ‘Print

Screen’.

③

-Remote status

When the instrument is under remote control via any interface

REM

will be

displayed.

USB

When a USB connection is detected, the USB icon will become activated

LAN

The

LAN

field in the Status Line can show multiple status indications:

There is no LAN connection, for example no cable connected.

Successfully connected.

(Flashing icon) Configuring LAN connection.

Unsuccessful attempt to connect.

④

Flash drive port

When a flash drive is detected in the flash drive port, the flash drive icon will

become activated.

①

②

③ ④

Summary of Contents for TGR2050 Series





































































































Search results

Summary of Contents for TGR2050 Series

Reviews:

Brands by name

Popular brands

Aim-TTI TGR2050 Series, Instruction Manual

Search results

Summary of Contents for TGR2050 Series

Reviews:

Brands by name

Popular brands