Aim-TTI TGR2050 Series Instruction Manual Download Page 71

Page: 71 / 100

13 - Utility menu

I/O

TGR2050 Series Instruction Manual

I/O

To access the I/O menu, press the UTILITY key, followed by

I/O

NOTE

GPIB will only be present if GPIB option is fitted.

LAN

The LAN interface is designed to meet LXI 1.5 LXI Device Specification 2016.

Remote control using the LAN interface is possible using the TCP/IP Socket protocol.

The instrument also contains a Web server which provides information on the unit

and allows it to be configured. Since it is possible to misconfigure the LAN interface,

making it impossible to communicate with the instrument over LAN, a LAN

Configuration Initialise (LCI) mechanism is provided via the user interface to reset the

unit to the factory default.
See ‘TGR2050 Series Programming Manual’ for further details. This can be found on

the Aim-TTi website:

www.aimtti.com

For more information on LXI standards refer to

www.lxistandard.org

Reset
To reset the LAN, touch

Reset

A pop-up will appear

‘Reset instrument’s LAN configuration to “default” and

reinitialise LAN port?’

Touch

Continue

to reset.

Summary of Contents for TGR2050 Series





































































































Search results

Summary of Contents for TGR2050 Series

Reviews:

Brands by name

Popular brands

Aim-TTI TGR2050 Series, Instruction Manual

Search results

Summary of Contents for TGR2050 Series

Reviews:

Brands by name

Popular brands