Aim-TTI TGR2050 Series Instruction Manual Download Page 12

Page: 12 / 100

5 - Rear Panel

Connections overview

TGR2050 Series Instruction Manual

⑤

External trigger in

DC coupled External Trigger Input signal, nominal threshold 1.65V

CAUTION

Do not apply external voltages exceeding ±10V to this socket.

⑥

Mod in/out

Analogue MOD IN, AC coupled 10k

Ω

input impedance, 1Vp-p full scale. Analogue

MOD OUT, DC coupled 150

Ω

source impedance, 2Vp-p full scale unloaded. Digital

MOD IN, DC coupled 10k

Ω

input impedance, nominal threshold of +1.65V. Digital

MOD OUT, DC coupled 150

Ω

source impedance, logic levels of <0.8V & >3V

unloaded.

CAUTION

Do not apply external voltages exceeding ±10V to this socket.

⑦

LAN

The LAN interface is designed to meet the LXI standard version 1.5 LXI Device

Specification 2016..

Remote control using the LAN interface is possible using the TCP/IP Socket protocol.

⑧

USB

The USB port accepts a standard USB cable. If the USB driver has been installed from

the website, the Windows plug-and-play function should automatically recognise

that the instrument has been connected. See the support page on the website for

information on installing the driver on a PC at

www.aimtti.com

⑨

GPIB (optional)

IEEE-488 The default GPIB address is 11.

Summary of Contents for TGR2050 Series





































































































Search results

Summary of Contents for TGR2050 Series

Reviews:

Brands by name

Popular brands

Aim-TTI TGR2050 Series, Instruction Manual

Search results

Summary of Contents for TGR2050 Series

Reviews:

Brands by name

Popular brands