Agria 3900 Operating Instructions Manual Download

Page: 57 / 74

Edition 04.97

Two-wheel tractor 3900

6. Troubleshooting

Observe safety instructions! Have all serious malfunctions on the machine or engine repaired
by your agria workshop. They have the proper tools. Improper repairs can only add to the damage.

Problem

Possible cause

Remedy

Page

Petrol engine

- Spark plug connector not connected

Connect spark plug connector

does not start

- Choke is not pulled

Set Choke-lever to
operating position “BETRIEB”

- Engine-off-switch is set to “0”

Set engine-off-switch to “I”

- Safety circuit is not set to start position

Set safety circuit to start position

- Fuel tank empty or poor fuel

Fill fresh fuel

- Fuel line clogged

Clean fuel line

- Defective spark plug

Clean, adjust or exchange spark plug

- Engine too much fuel

Dry and adjust spark plug and

(“flooded engine”)

start at full throttle

- Engine-off-line defective

Check line and connections

- Inleaked air due to loose caburetor

Tighten fastening screws

and suction line

Misfirings in

- Engine running in CHOKE range

Set CHOKE-lever to

petrol engine

operating position “BETRIEB”

Fix ignition cable retaining device

- Clogged fuel line or poor fuel

Clean fuel line,fill fresh fuel

- Vent opening in fuel tank cap clogged

Exchange fuel tank cap

- Water or dirt in fuel system

Drain fuel and fill fresh fuel

- Air filter clogged

Clean air filter or exchange

- Carburetor misadjusted

Re-adjust carburetor

Excessive

- Low engine oil level

Refill oil immediately

temperature

- Impaired cooling

Clean cooling fan grille,

in petrol engine

clean internal cooling fins

- Air filter clogged

Clean air filter

- Carburetor misadjusted

Re-adjust carburetor

Misfirings in

- Short firing intervals

Adjust spark plug

petrol engine

- Incorrect idle mix

Adjust carburetor

at high speeds

Petrol engine

- Firing interval too long,

Adjust or replace spark plug

frequently

defective spark plug

stalls

- Carburetor misadjusted

Re-adjust carburetor

in idle

- Air filter clogged

Clean air filter

Summary of Contents for 3900











































































Search results

Summary of Contents for 3900

Reviews:

Related manuals for 3900

Brands by name

Popular brands

Agria 3900, Operating Instructions Manual

Search results

Summary of Contents for 3900

Reviews:

Related manuals for 3900

Brands by name

Popular brands