Agria 2500 Hydro Operating Instructions Manual Download Page 46

Page: 46 / 70

agria-

Two-Wheel Tractor 2500 Hydro

5. Maintenance

Diesel Engine

Dry-Type Air Filter

When You take up operation
check the air filter (D4) on dirt,
clean it if necessary.
Clean air filter (J/4) after a maxi-
mum of every 50 operating hours
or at least after 3 months, in
case of heavy dust occurence
even earlier.

Clean air filter and outside

surrounding parts.

Remove the wing nut and air

filter cap including the cyclone
pre-filter.

Rotate the air filter cap to al-

low any dirt inside the cyclone
pre-filter drop out.

Carefully remove foamed

pre-filter.

Wash foamed pre-filter in de-

tergent and water (no petrol).

Squeeze foamed pre-filter

and dry it.

Remove paper filter element

Sightly tap the element on a

smooth surface.

Do not use compressed air

to blow out dust of foamed pre-
filter and paper filter element.
Do not treat with oil.

Re-insert the filter element

and attach the foamed pre-filter.

Reposition air filter cap and

fasten with wing nut.
Replace paper filter element af-
ter every 400 operating hours or
at least once a year.

Replace immediately
damaged filter elements.

Wing nut

Paper filter element

Foamed pre-filter

Air filter cap
Cyclone pre-filter

A, 50 h

(400 h)

Summary of Contents for 2500 Hydro







































































Search results

Summary of Contents for 2500 Hydro

Reviews:

Agria 2500 Hydro, Operating Instructions Manual, Page: 46 / 70

Search results

Summary of Contents for 2500 Hydro

Reviews: