Agora Models JAGUAR E-TYPE Page 39 Build Instructions Download | Manualshive

Page: 39 / 55

background image

AGORA

MODELS

39

5

7

6

8

Fit the motif bar onto the bumper and attach using an AG09 screw.

The front bumpers and motif bar should look like this once assembled.
The inset shows the Jaguar growler badge.

Repeat for the other bumper, attaching with another AG09 screw.

Now take the bonnet under panel and align the front bumper
assembly with it as shown.

Stage 97: Attaching the Front Bumper

and Underside

AG09

AG09

«
...
37
38
39
40
41
...
»

Summary of Contents for JAGUAR E-TYPE
























































Reviews:

No comments

Related manuals for JAGUAR E-TYPE

Brand: Team C Pages: 35

Brand: Team Magic Pages: 22

Mini Inferno ST 09

Brand: Kyosho Pages: 57

Brand: VBC Racing Pages: 20

Brand: Hobbytech Pages: 36

CE-10T Brushless NEW GENERATION

Brand: Carson Pages: 72

Brand: REVELL Pages: 12

Brand: Arrma Pages: 14

Brand: Arrma Pages: 20

Brand: Shift3 Pages: 4

HOT SHOT AB2.8 BL

Brand: Absima Pages: 38

Brand: Absima Pages: 50

Brand: Jamara Pages: 12

Brand: Jamara Pages: 8

Brand: Helion Pages: 40

Adventure FI000202G33

Brand: Peg-Perego Pages: 28

Brand: Peg-Perego Pages: 52

Brand: Traxxas Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands