Agilent Technologies E8363BU-014 Installation Note Download Page 23 | Manualshive

Page: 23 / 24

background image

Installation Note E8364-90019

23

Step 11. Perform Post-Upgrade Adjustments and Calibration

Adjustments

The following adjustments must be made due to the hardware changes of the analyzer.
• source calibration
• receiver calibration
These adjustments are described in the PNA service guide and in the PNA on-line HELP. A

list of equipment required to perform these adjustments can be found at

Required for Post-Upgrade Adjustments” on page 8

Calibration

The analyzer should now operate and phase lock over its entire frequency range.
If you experience difficulty with the basic functioning of the analyzer, contact Agilent. Refer to

“Contacting Agilent” on page 3

• Although the analyzer functions, its performance relative to its specifications has not been

verified.

• It is recommended that a full instrument calibration be performed using the PNA

performance test software.

• Refer to the analyzer’s service guide for information on the performance test software.

«
...
21
22
23
24
»

Summary of Contents for E8363BU-014

























Reviews:

No comments

Related manuals for E8363BU-014

Brand: Icare Pages: 3

Brand: Candela Pages: 4

Brand: Valhalla Scientific Pages: 43

YPP-100 Light Piano

Brand: Yamaha Pages: 54

Brand: Yamaha Pages: 44

Brand: Yamaha Pages: 56

Brand: Yamaha Pages: 10

Brand: Yamaha Pages: 32

Brand: Hach Pages: 96

Brand: GE Pages: 35

Brand: Yamaha Pages: 24

Brand: Hanna Instruments Pages: 2

Brand: Omega Pages: 13

WM14-96 - PROGRAMMING

Brand: CARLO GAVAZZI Pages: 6

K-PATENTS PR-43

Brand: Vaisala Pages: 54

Brand: CryptOn Pages: 13

Brand: Keysight Technologies Pages: 10

Brand: MFJ Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands