Agilent Technologies E8363BU-014 Installation Note Download Page 16 | Manualshive

Page: 16 / 24

background image

16

Installation Note E8364-90019

Analyzers WITH Option UNL but WITHOUT Option 016

Refer to

for the following procedure. The new parts referenced in this procedure are

listed in

Table 1 on page 5

Install these cables

in the order listed

. Use a 5/16-inch torque wrench set to 10 in-lbs.

• W71 E8364-20177 REFERENCE 2 RCVR R2 IN to A29 channel R2 mixer
• W70 E8364-20176 REFERENCE 1 RCVR R1 IN to A28 channel R1 mixer
• W68 E8364-20044 A26 test port 1 coupler to PORT 2 CPLR ARM
• W72 E8364-20046 PORT 2 RCVR B IN to A30 channel B mixer
• W82 E8364-20054 A37 step attenuator to PORT 2 SOURCE OUT
• W84 E8364-20040 PORT 2 CPLR THRU to A39 bias tee
• W66 E8364-20048 Channel R2 detector to REFERENCE 2 SOURCE OUT
• W67 E8364-20043 A25 test port 1 coupler to PORT 1 CPLR ARM
• W69 E8364-20045 PORT 1 RCVR A IN to A27 channel A mixer
• W81 E8364-20053 A36 step attenuator to PORT 1 SOURCE OUT
• W83 E8364-20039 PORT 1 CPLR THRU to A38 bias tee
• W65 E8364-20047 Channel R1 detector to REFERENCE 1 SOURCE OUT

Figure 9

Cable Installation, Analyzers with Option UNL but without Option 016

«
...
14
15
16
17
18
...
»

Summary of Contents for E8363BU-014

























Reviews:

No comments

Related manuals for E8363BU-014

Brand: dacell Pages: 22

Brand: Hach Pages: 145

Brand: Hach Pages: 358

Polymetron 9582sc

Brand: Hach Pages: 280

Brand: HACH LANGE Pages: 15

Brand: YOKOGAWA Pages: 16

Electone Stagea ELS-01C

Brand: Yamaha Pages: 248

Brand: Clavitech Pages: 56

Brand: Hanna Instruments Pages: 28

ACCURE 2350-GAS

Brand: ROOTECH Pages: 26

Brand: THORLABS Pages: 49

Brand: RaySafe Pages: 2

WTW SensoLyt 900

Brand: Xylem Pages: 12

Brand: Hanna Instruments Pages: 32

Brand: Alcor System Pages: 21

Orion 64989-002

Brand: Badger Meter Pages: 16

CONTISYS OBD - V3.0

Brand: VDO Pages: 144

Brand: MED Associates Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands