Agilent Technologies E8363BU-014 Installation Note Download Page 5

Page: 5 / 24

Installation Note E8364-90019

Items Included in the Upgrade Kit

Check the contents of your kit against this list. If any item is missing or damaged, contact

Agilent Technologies. Refer to

“Contacting Agilent” on page 3

Table 1

Contents of Option 014 Upgrade Kit (E8364-60103)

Ref

Desig.

Description

Qty

Part Number

These parts are for ALL analyzers

Installation note (this document)

E8364-90019

ROHS addendum

9320-6722

Cable clamp

1400-1439

W60

Front-panel jumper

E8364-20059

W65

RF cable, channel R1 detector to REFERENCE 1 SOURCE OUT

E8364-20047

W66

RF cable, channel R2 detector to REFERENCE 2 SOURCE OUT

E8364-20048

W67

RF cable, A25 test port 1 coupler to PORT 1 CPLR ARM

E8364-20043

W68

RF cable, A26 test port 2 coupler to PORT 2 CPLR ARM

E8364-20044

These parts are for analyzers WITHOUT Option UNL OR Option 016

Lower front panel overlay (Option 014)

E8364-80003

W61

RF cable, A22 switch splitter to PORT 1 SOURCE OUT

E8364-20081

W62

RF cable, A22 switch splitter to PORT 2 SOURCE OUT

E8364-20082

W63

RF cable, PORT 1 CPLR THRU to A25 test port 1 coupler

E8364-20073

W64

RF cable, PORT 2 CPLR THRU to A26 test port 2 coupler

E8364-20074

W69

RF cable, PORT 1 RCVR A IN to A27 channel A mixer

E8364-20045

W70

RF cable, REFERENCE 1 RCVR R1 IN to A28 channel R1 mixer

E8364-20075

W71

RF cable, REFERENCE 2 RCVR R2 IN to A29 channel R2 mixer

E8364-20076

W72

RF cable, PORT 2 RCVR B IN to A30 channel B mixer

E8364-20046

These parts are for analyzers WITH Option UNL but WITHOUT Option 016

Lower front panel overlay (Option UNL/014)

E8364-80011

W69

RF cable, PORT 1 RCVR A IN to A27 channel A mixer

E8364-20045

W70

RF cable, REFERENCE 1 RCVR R1 IN to A28 channel R1 mixer

E8364-20176

W71

RF cable, REFERENCE 2 RCVR R2 IN to A29 channel R2 mixer

E8364-20177

W72

RF cable, PORT 2 RCVR B IN to A30 channel B mixer

E8364-20046

W81

RF cable, A36 step attenuator to PORT 1 SOURCE OUT

E8364-20053

W82

RF cable, A37 step attenuator to PORT 2 SOURCE OUT

E8364-20054

W83

RF cable, PORT 1 CPLR THRU to A38 bias tee

E8364-20039

W84

RF cable, PORT 2 CPLR THRU to A39 bias tee

E8364-20040

Summary of Contents for E8363BU-014

























Search results

Summary of Contents for E8363BU-014

Reviews:

Related manuals for E8363BU-014

Brands by name

Popular brands

Agilent Technologies E8363BU-014, Installation Note

Search results

Summary of Contents for E8363BU-014

Reviews:

Related manuals for E8363BU-014

Brands by name

Popular brands