Agilent Technologies E8363BU-014 Installation Note Download Page 22

Page: 22 / 24

Installation Note E8364-90019

Step 10. Enable Option 014

Procedure Requirements

• The analyzer must be powered up and operating to perform this procedure.
• The Network Analyzer program must be running.
• A mouse must be connected to the analyzer for this procedure.

Option Enable Procedure

1. On the analyzer’s

System

menu, point to

Service

, and then click

Option Enable

2. In the

Select Desired Option

list, click

014 - Configurable Test Set

3. Click

Enable

4. Click

Yes

in answer to the displayed question in the

Restart Analyzer?

box.

5. When the installation is complete, click

Exit

Option Verification Procedure

Once the analyzer has restarted and the Network Analyzer program is again running:
1. On the analyzer’s

Help

menu, click

About Network Analyzer

2. Verify that “014” is listed after “Options:” in the display.

3. Click

to close this screen.

NOTE

If Options 014 has not been enabled, perform the

”Option Enable

Procedure”

again. If the option is still not enabled, contact Agilent

Technologies. Refer to

“Contacting Agilent” on page 3

Summary of Contents for E8363BU-014

























Search results

Summary of Contents for E8363BU-014

Reviews:

Related manuals for E8363BU-014

Brands by name

Popular brands

Agilent Technologies E8363BU-014, Installation Note

Search results

Summary of Contents for E8363BU-014

Reviews:

Related manuals for E8363BU-014

Brands by name

Popular brands