Agilent Technologies E8363BU-014 Installation Note Download Page 8 | Manualshive

Page: 8 / 24

background image

8

Installation Note E8364-90019

Overview of the Installation Procedure

Step 1. Remove the Outer Cover.
Step 2. Remove the Front Panel Assembly.
Step 3. Raise the Receiver Deck.
Step 4. Remove the Existing Cables.
Step 5. Install the Option 014 Cables.
Step 6. Lower and Fasten the Receiver Deck.
Step 7. Replace the Lower Front Panel Overlay.
Step 8. Reinstall the Front Panel Assembly and Install Front Panel Jumpers.
Step 9. Reinstall the Outer Cover.
Step 10. Enable Option 014.
Step 11. Perform Post-Upgrade Adjustments and Calibration.

Tools and Equipment Required for the Installation

CAUTION

Use a 5/16-inch torque wrench set to 10 in-lbs on all cable connections except the

front-panel adapters to which the front-panel jumpers attach. Use a 5/16-inch

torque wrench set to 21 in-lbs for these connections.

Equipment Required for Post-Upgrade Adjustments

Description

Qty

Part Number

T-10 TORX driver (set to 9 in-lbs)

1

N/A

T-20 TORX driver (set to 21 in-lbs)

1

N/A

5/16-inch torque wrench (set to 10 in-lbs)

1

N/A

5/16-inch torque wrench (set to 21 in-lbs)

1

N/A

ESD grounding wrist strap

1

9300-1367

5-ft grounding cord for wrist strap

1

9300-0980

2 x 4 ft conductive table mat and 15-ft grounding wire

1

9300-0797

ESD heel strap (for use with conductive floors)

1

9300-1308

Equipment Type

Model or

Part Number

Alternate Model or

Part Number

Power meter

E4418B/E4419B

E4418A/E4419A

Power sensor, 2.4 mm

8487A

None

Adapter, 2.4 mm (f) to 2.4 mm (f)

11900B

85056-60007

RF cable, 2.4 mm (f) to 2.4 mm (f)

85133C

85133E

«
...
6
7
8
9
10
...
»

Summary of Contents for E8363BU-014

























Reviews:

No comments

Related manuals for E8363BU-014

Brand: Qu-Bit Electronix Pages: 10

Brand: Tavool Pages: 12

Brand: Kawai Pages: 36

Brand: JUMO Pages: 150

Brand: Hanna Instruments Pages: 24

Brand: YZXStudio Pages: 3

LaserRange-Master i5

Brand: LaserLine Pages: 68

Brand: Hanna Instruments Pages: 2

28APE190008/AI481

Brand: Apera Instruments Pages: 13

Brand: Voweek Pages: 20

Brand: Extech Instruments Pages: 8

SourceMeter 2460

Brand: Keithley Pages: 24

Brand: PCB Piezotronics Pages: 17

Brand: Milwaukee Pages: 2

Brand: Xylem Pages: 26

Brand: Hanna Instruments Pages: 2

Brand: ion science Pages: 30

MicroPolar LB 566

Brand: Berthold Pages: 176

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands