manualshive.com logo in svg

Agilent Technologies 16712A, Help Manual

Share
Download
Agilent Technologies 16712A Help Manual Download Page 109

108

Chapter 1: Agilent Technologies 16712A 128K Sample Logic Analyzer

Analyzer Probing Overview

Adapter-to-Board Connection

Both the 01650-63203 and the E5346A adapters include termination 
for the logic analyzer. The 01650-63203 termination adapter plugs into 
a 2 x 10 pin header with 0.1 inch spacing. The E5346A high-density 
adapter connects to an AMP "Mictor 38" connector. If possible, use 
support shrouds around the Mictor connector to relieve strain and 
improve connections.

Direct Pod-to-Board Connection

If you provide proper termination as part of the target board, you can 
plug the pod directly into the ©3M 2520-series, or similar alternative 
connector. Suggested termination is shown in the 

Logic Analysis 

System and Measurement Modules Installation Guide

.

Also use this termination with the Agilent Technologies E5351A high-
density, non-terminated adapter.

Pod-to-Analysis Probe Connection

Analysis probes (formerly called preprocessors) are microprocessor-
specific interfaces that make it easier to probe buses. Generally, 

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for 16712A
























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands