AGCO FENDT 700 Vario S4 Series Workshop Service Manual Download

Page: 4 / 51

1. Tractor

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-3

1.1.1 Notes on documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

1.1.2 Safety briefing and measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

1.1.3 Importance of and position of the safety decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

1.1.4 Note on hydraulics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18

1.1.5 Assignment table FENDT T types to the EU Type Approval Number . . . . . . . . . . . . . . . . 1-19

1.1.6 Change wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20

1.1.7 Location of the identification plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22

1.1.8 Biodegradable hydraulic oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-25

1.1.9 Tightening torque for screws with a galvanized surface . . . . . . . . . . . . . . . . . . . . . . . . . 1-26

1.1.10 Tightening torque for screws and bolts with VDA coating . . . . . . . . . . . . . . . . . . . . . . 1-27

1.2 Technical specification

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-29

1.2.1 Technical data: 0000 general . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-29

1.2.2 Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-30

1.2.3 Technical specification: Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-37

1.2.4 Front axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-45

1.2.5 Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-47

1.2.6 Air conditioning / Cab / EPC control valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-47

1.2.7 Compressed air system / Electrical system / Front power lift . . . . . . . . . . . . . . . . . . . . . 1-48

1.2.8 Hydraulic equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-49

1.3 Fault code tables

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-53

1.3.1 Note on the fault code table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-53

1.3.2 Confirming, calling up, deleting fault codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-53

1.3.3 Fault code 00.0.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-55

1.3.4 Fault code 01.0.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-59

1.3.5 Error code 02.1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-64

1.3.6 Error code 03.1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-66

1.3.7 Fault code 04.1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-68

1.3.8 Fault code 05.1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-81

1.3.9 Fault code 06.1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-86

1.3.10 Fault code 07.1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-91

1.3.11 Fault code 08.1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-93

1.3.12 Fault code 09.1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-99

1.3.13 Fault code 0A.1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-104

1.3.14 Fault code 0B.1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-124

1.3.15 Error code 0D.1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-127

1.3.16 Fault code 0E.1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-130

1.3.17 Error code 0F.1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-135

1.3.18 Fault code 10.1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-138

1.3.19 Error code 11.1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-140

1.3.20 Fault code 14.1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-141

1.3.21 Fault code 15.1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-145

1.3.22 Fault code 17.1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-146

1.3.23 Fault code 18/01/2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-147

1.3.24 Fault code 1D.1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-150

1.3.25 Fault code 1F.1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-162

1.3.26 Error code 20.1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-163

1.3.27 Fault messages: manual air conditioning system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-168

1.3.28 Calibration fault codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-169

1.4 Component position

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-181

Table of contents

FENDT 700 Vario S4

1-1

X990.005.538.013

Find manuals at https://best-manuals.com

Summary of Contents for FENDT 700 Vario S4 Series




















































Search results

Summary of Contents for FENDT 700 Vario S4 Series

Reviews:

Related manuals for FENDT 700 Vario S4 Series

Brands by name

Popular brands

AGCO FENDT 700 Vario S4 Series, Workshop Service Manual

Search results

Summary of Contents for FENDT 700 Vario S4 Series

Reviews:

Related manuals for FENDT 700 Vario S4 Series

Brands by name

Popular brands